Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
The pumping unit will heat the water as it pumps. Cover the hydrotherapy spa with the spa cover. The spa cover must be tight (see SECURING THE SPA COVER ON THE SPA on this page). The water will heat at about 6°F per hour with the cover on. If you are using the spa indoors, and the room temperature is maintained at 70°F, it will take approximately 6 to 8 hours for the water to reach the set temperature. The temperature and the water flow can be set or changed with the controls on the console (see USING THE CONTROLS on page 12). SECURING THE SPA COVER ON THE SPA To secure the spa cover, snap the latches on the spa cover into the buckles on the premium cedar panels. To lock the buckles, insert the key and turn it clockwise 1/4 turn. To unlock the buckles, insert the key and turn it counterclockwise 1/4 Latch Key Buckle turn. Always keep the buckles locked when the spa is not in use. Keep the keys in a safe place, out of the reach of children. 10 Spa Shell Diagram Spa Shell Diagram A LB D I E I H F G M M M J J L L L L K K K KK K K K G C N L L A. The filter can be removed for cleaning or replacement (see CHECKING AND CLEANING THE FILTER on page 13). B. The underwater light can be used for night operation (see USING THE CONTROLS on page 12). The spa includes both red and blue covers for the light. C. The temperature probe monitors water temperature. D. The volcano jet provides a soothing foot massage. E. The whirlpool jet diverts the water flow three different ways. By turning the outer ring, you can divert the water flow between the volcano jet (D), the other jets on the spa, and the whirlpool jet (E), which creates a whirlpool action. Note: The outer ring may be hard to turn while the pump is turned on high. F. The three suction fittings provide water to the pumps. The suction covers should always be in place over the fittings. Never operate the spa without the suction covers in place. G. The two ozone jets provide ozone sanitation to the spa. The ozone generator engages during the spa’s filtration cycles to destroy algae, viruses, and bacteria while breaking down chemicals and solids for easy removal by the filtration system. Ozone oxidizes combined chlorine and bromine, freeing them to be continuously re-used, reducing the chemical needs and costs of the spa’s sanitation. H. The console controls the spa jets, turns the underwater light on and off, and adjusts the water temperature setting (see USING THE CONTROLS on page 12). I. The four air controls regulate the air flow to the whirlpool and volcano jets. J. The two neck jets can be adjusted to spray soothing water on your neck. To activate the neck jets, either pull the nozzles or turn the nozzles clockwise. To turn the neck jets off, push the nozzles or turn the nozzles counterclockwise. K. The twenty rotary jets provide a spinning massage. L. The dual rotary jets provide a pulsating massage action. Rotate the outer ring counterclockwise to turn the jets on. Rotate the outer ring clockwise to turn the jets off. M. The three variable-flow jets are fully adjustable. Turn the outer rings to regulate the flow. N. The power massage jet provides a soothing massage to your lower back. Turn the outer ring to regulate the flow. 11 Using the Controls Air Controls Air Controls Temperature Button Light Button Pump Button 2 Pump Button 1 Display Refer to the diagram above. The function of each control is explained below: Pump Button 1: Turns the jets labeled on page 11 with boxed letters on and off. If the button is pressed once, the pump will run at the low setting. If the button is pressed twice, the pump will run at the high setting. If the button is pressed a third time, the pump will shut off. Note: If the spa is heating or running a filter cycle, the pump will turn on at the low setting. If the pump is left on the low setting, it will automatically shut off after 2 hours. If the pump is left on the high setting, it will automatically shut off after 30 minutes. The spa also features an automatic mode that heats and filters the water when the spa is left unattended. When the power to the spa is first turned on, or if the buttons on the console have not been pressed for longer than twenty minutes, the automatic mode will be activated. Note: To keep the filter and heat cycles from running, the power to the spa must be shut off at the breaker box. Pump Button 2: Turns the remaining spa jets on and off. If the button is pressed once, the jets will run, providing gentle hydrotherapy. If the button is pressed again, the jets will shut off. If the pump is left running, it will automatically shut off after 30 minutes. Temperature Buttons: Control the temperature setting of the water. The temperature can be set from 80°F to 104°F. The water heats at about 1.8°F per hour with the cover on. Use a medical or other accurate thermometer to check the temperature of the water. Note: The word “COOL” will appear in the console display if the temperature of the water is more than 20°F...
Otros modelos de este manual:Otros accesorios para la casa - PFSW73900, PFSB73900, PFG73900 (492.11 kb)