Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
• Test the water regularly to ensure proper levels of sanitizers, pH, and other water care requirements. • Drain, clean, and refill your spa with fresh water on a regular schedule, and in accordance with this owner’s manual. • Clean the filter(s) at least once per month. • Check to make sure you have proper circulation throughout your spa water system. • Have spa users bathe before entering the spa water. SPA LEVELING PREPARATION Concrete sloped at 1/2 inch (1.3 cm) per 10 feet (305 cm) is preferred so that rain water and water spillover will run off and not puddle underneath the spa (water under the spa for long periods of time may cause the wood to deteriorate). Other options are brick, stepping stone, or blocks. It is important to note that soft surfaces, even when stepping stones are used to evenly distribute the weight of the spa, will have a tendency to settle, thus resulting in an unleveled spa. NOTE: Placing the spa on grass or dirt may increase the amount of debris which is inadvertently brought into the spa water and may cause harm to your equipment as well as the spa surface, which is not covered under warranty. 10 ft. (305 cm) 1/2 inch (1.3 cm) Stepping stones or brick may settle Slope 1/2 inch per 10 ft. for proper drainage. causing the spa to be unlevel. SPA COVER INSTALLATION • Place the cover squarely on the spa. • Position the tie-down locks included with your cover on the side of the spa so that they are easily reached by the cover tie-down straps. Allow for about 1/2” to 3/4” slack in the straps to make it easy to insert straps into locks and to compensate for vinyl shrinkage in cold weather. • Attach the locks with the screws provided and insert the cover tie-down straps into the locks. NOTE: Keeping the cover in place any time the spa is not in use will reduce the amount of time the heater operates, thereby minimizing operating costs. COVER INSTALLATION TIE-DOWN STRAP LOCK COVER KEY SCREW (2) DANGER. RISK OF INJURY. • Never leave a spa uncovered or unattended. • Never leave a spa cover unlocked. • Do not stand, sit, or lie on the cover. 4 START-UP AND REFILL PROCEDURES Your spa has been thoroughly tested during the manufacturing process to ensure reliability and long-term customer satisfaction. A small amount of water may have remained in the plumbing after testing and, as a result, may have spotted the spa shell or the spa siding prior to delivery. Before filling the spa, wipe the spa shell clean with a soft rag. The following instructions must be read and followed exactly to ensure a successful start-up or refill. CAUTIONS • Do not fill the spa with hot water, as tripping of the high-limit thermostat may result. • DO NOT CONNECT POWER TO AN EMPTY SPA. Power to the spa automatically activates critical components within the spa, such as controls, heater, and other systems. If power is supplied to these components prior to the spa being filled, the components will be damaged, and this may result in a non-warranty component failure. • Do not use your spa after filling until all of the steps listed below are completed. • Do not add chlorine if treating your spa with polyhexamethylene biguanide (Biguanide, PHMB, eg. BaquaSpa®) sanitizer. • Before filling your spa for the first time, remove the equipment compartment door and check to ensure that the unions on either side of the pump(s) and heater are hand-tight. 1. Ensure that the drain is closed and remove the filter compartment cover, skimmer basket, weir, and filter. Then insert the end of a garden hose into the filter canister and begin filling the spa. The water level of your spa should be maintained at a level one inch above the highest jet in the spa excluding the four above-the-waterline neck jets in the EsctaSeat®. Reinstall the filter and then the skimmer basket, and weir once the spa is filled. IMPORTANT: Watkins® Manufacturing Corporation does not recommend that the spa be filled with “softened” water, as this may damage the spa’s equipment. 2. AFTER the spa has been filled with water and the equipment compartment door is secured, power must be applied to the spa. 3. The jet pump(s), heating system and all internal plumbing will achieve a partial prime as the spa is filled. To check the operation of the jet system and to purge any remaining air from the heating system, push the “JETS” button icon on the control pad three times to make the jet pump(s) run on high speed for one minute. Once the jet system is fully operational (as indicated by strong, non-surging jets), priming of the spa is complete. If you do not feel a steady stream of water from your jets, refer to the instructions for priming the pump in the SPA TROUBLESHOOTING section in the back of this manual. 4. Adjust Total Alkalinity (TA) to 125 ppm, Calcium Hardness (CH) to 150 ppm, then spa water pH to between 7.4 and 7.6. These procedures are listed in the “Water Quality and Maintenance” section. IMPORTANT: Add spa water chemicals directly into the filter compartment a...
Otros modelos de este manual:Otros accesorios para la casa - C30 (1.96 mb)
Otros accesorios para la casa - C45 (1.96 mb)
Otros accesorios para la casa - C45S (1.96 mb)