Votos - 3, Puntuación media: 4 ( )

Fabricar: Desa Tamaño del archivo: 3.3 mb Nombre del archivo: Idioma del manual:

Bubbles forming show a leak. Correct all leaks at once. Do not operate any appliance if a leak is detected. Figure 12- Typical Exterior Wall Gas Shutoff Installation Key Extension Shutoff Valve Figure 13 - Gas Line Routing Figure 14 - Sediment Trap PILOT ADJUSTMENT The pilot or electrode assembly is factory preset for the proper flame height. Alterations to these settings may have occurred during shipping and handling. If this is the case, some minor readjustments may be necessary and should be done by a qualified service technician. The proper settings for the thermopile height should be at a distance of 3/8" (.95 cm) to 1/2" (1.27 cm) from the pilot flame as shown in Figure 15. Figure 15 - Pilot Assembly 3" Min. Sediment Trap (Not Supplied) Incoming 1/2" Gas Line Permitted By Local Codes 3" Min. (7.6 cm) 1/8" (0.3cm) 3/8" - 1/2" (.95cm-1.3cm) Complete your gas line installation by connecting the incoming gas line to the flexible gas line. Secure tightly with a wrench but do not over-tighten. T IP OFF TOL ON PILO TPTH TP TH Gas Routing (Right Side Not Shown) Side of Fireplace Front Face INSTALLATION Gas Line Hook-Up Pilot Adjustment 111916-01A Forr morre iinfforrmattiion,, viisiitt 99 INSTALLATION Continued REMOVING GLASS PANEL CAUTION: Before you proceed, make sure your gas control valve is in the OFF position. 1. To remove louvers, pull both spring latches (located in each end of louver) toward center of appliance at the same time until disengaged from locating holes. Repeat for bottom end spring latches (see Figure 16). 2. Remove screen rod by removing rod loop from glass door center bracket. Slide screen rod either to the left or right of fireplace until one end is free to completely remove screen from fireplace. 3. Undo latches located on top and bottom of firebox (see Figure 17). Carefully swing door to the left. The glass door is securely mounted to the firebox with 5 screws. Figure 16 - Removing Louvers Figure 17 - Spring Latches INSTALLING LOG SET Each log is marked with a number in the following diagram. These numbers will help in identifying the logs when installed. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with fireplace. Models CD32M and CD36M-A Series 1. Place log #1 (back log) on top of grate as shown in Figure 18. Make sure notches in bottom of log fit over grate. 2. Place log #2 (large front log) over pins on grate (see Figure 19). Figure 18 - Installing Log #1, Models CD32M/CD36M-A Series Figure 19 - Installing Log #2, Models CD32M/CD36M-A Series Glass Locating Holes Spring Latch Bottom Louver Open Close 1 2 3. Place log #3 (c-shaped crossover log) onto rear and front logs as shown in Figure 20. Make sure it is seated properly on the smooth surface on front log and on the pin on back log. 4. Place log #4 (small round log) on pin on right side of front log (see Figure 21). 5. Place log #5 (small front log) onto the front left part of grate making sure notches fit over prongs of grate (see Figure 22). 6. Place log #6 onto two pins on left side of back and front logs (see Figure 22). 3 Figure 20 - Installing Log #3, Models CD32M/CD36M-A Series 4 Figure 21 - Installing Log #4, Models CD32M/CD36M-A Series 5 6 Figure 22 - Installing Logs #5 and #6, Models CD32M/CD36M-A Series INSTALLATION Removing Glass Panel Installin Log Set 111916-01A Forr morre iinfforrmattiion,, viisiitt 10 INSTALLATION Continued Figure 23 - Installing Log #1, Model CD42M-A Figure 24 - Installing Log #2, Model CD42M-A Figure 25 - Installing Log #3, Model CD42M-A Figure 26 - Installing Log #4, Model CD42M-A Figure 27 - Installing Log #5, Model CD42M-A Figure 28 - Installing Logs #6 and #7, Model CD42M-A Model CD42M-A 1. Place log #1 (small base log) onto pin on left side of grate extension (see Figure 23). 2. Rest left side of log #2 (front log) on top of log #1 and right side onto pin located on right side of grate extension (see Figure 24). 3. Place log #3 (rear log) onto pins on rear of grate (see Figure 25). 4. Place log #4 (crossover log) onto pins from both logs #2 and #3 (see Figure 26). 5. Place log #5 (top log) onto right pin of front log (#2) and smooth surface of rear log (#3). Make sure it is seated properly (see Figure 27). 11 2 3 6. Place log #6 (left log) on left pin of front log (#2) and smooth surface of rear log (#3). Make sure it is seated properly (see Figure 28). 7. Place log #7 (right log) on right pin of top log (#5). Make sure it is seated properly (see Figure 28). 5 6 7 4 INSTALLATION Installing Log Set (Cont.) INSTALLATION Installing Log Set (Cont.) Decorative Facing Face Extension for Model DC32M Only BURNER FLAME ADJUSTMENT 11 INSTALLATION Continued Lava Rock and Ember Material 1. For all models, place lava rock along sides and front of firebox bottom in areas that are visible. It is not necessary to use all lava rock provided. NOTICE: Do not put lava rock on or under burner. Placing lava ro...

Descargar ahora

Introduzca dos números de la imagen: