Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Contact your authorized dealer. 14.0 Troubleshooting Procedures In the event your Sundance spa is not working the way it should, please first review all the installation and operating instructions in this manual and check the message on the panel display. If you are still not satisfied it is working properly, please follow the appropriate troubleshooting instructions. Note: If any of the supply cords to the accessories are damaged, they must be replaced by authorized service personnel. 14.1 None of the Components Operate (e.g. Pump, Light) Check the following: 1. Is there power to the spa? 2. Is the household circuit breaker tripped? 3. Call your authorized dealer. 14.2 Pump does Not Operate but Light does Press the JETS 1 Button: 1. If no water movement is detected, make sure power is going to the spa and check the water level. If it does not solve the problem, contact your authorized Sundance dealer. 2. The main pump operates but no water flows to jets. Pump may not be properly primed. This can happen after the spa is drained and refilled. Press the JETS 1 button several times, never leaving the motor on for more than 5 to 10 seconds at a time. Turn power off and let the air out by loosening the cap on the massage selector and/ or removing the filter.Make certain you tighten the massage selector cap and/or reinstall the filter before turning on spa power and restarting the pump. Page 46 ELITE SERIES ELITE SERIES Poor jet Action 1. Press the JETS 1 button to make certain the pump #1 is on. 2. Rotate the air control clockwise to the “on” position. 3. Check for dirty filter. Clean, if necessary. 4. Make sure jets are all the way open. 14.4 Water is Too Hot Reduce thermostat setting so the heater turns off. 14.5 No Heat 1. Check thermostat setting. 2. Keep the spa cover in place while heating. 3. Check the settings to see if your spa is in economy filtration/heating mode (pages 32-33). Should checking the above steps fail to correct the problem, please call your dealer so that they may arrange service. We build the best spas in the industry. Nonetheless, we are always striving to improve the quality and features of our products. Your input as a Sundance spa owner is a cherished part of this process. If you have any comments or suggestions, or if you wish to be informed on any new products for your spa, please write to us. CONGRATULATIONS on your good taste and welcome to the happiest and most relaxed family in the world! Page 47 ELITE SERIES ELITE SERIES North American Circuit diagram This wiring diagram is used for all North American 240 VAC (60 Hz) dedicated power models. Stereo(Optional) Power Supply Ozonator( optional) O 3 GRNTB1 Standard 240 VAC, 3-Wire Connection (60 Hz, 1-USE COPPER CONDUCTORS ONLY. WIRE SIZE MUSTBE APPROPRIATE PER NEC AND/OR LOCAL CODESRED REDJ6 BLKJ5 WHTWHTWHTREDBLKBLKBLK RED REDBLK BLK BLK 21 Flow switchHi - limit / freeze sensorLogic Jumper Settings (Factory Defaults Shown)JP1 1-2 ON = 40A Logic JP1 1-2 OFF = 50A Logic (Factory Default Setting) JP1 3-4 ON = 2 Pump OperationJP1 3-4 OFF = 1 Pump OperationJP1 5-6 ON = 60A Logic (Remove JP1 1-2 Jumper) JP1 5-6 OFF = Leave off for 40A or 50A LogicJP1 7-8 ON = °C Temperature DisplayJP1 7-8 OFF = °F Temperature Display J1 J2J3 F130A, 250VSC-30 Pump 1 Transformer240 VACJ4F1 JP1 42 31 6 5 8 7 HILO C Control Panel Circ.Pump J20 K1J21J11J12J13J14J15J16J17J18J19 J8 J9 J10 This device complies with Part 15 of theFCC rules. Operation is subject to thefollowing two conditions:1. This device may not cause harmful interference. 2. This device must accept any inteference received including interference cause undesired operation. Heater5.5 kW240 VAC Pump 2 HI RED BLK J7 Blue wires 12 VACconstant voltage(connects to theyellow wires onthe transformer) LightDCU Waterfall, Accessories, Air controls and Footwelllights can connect to anyplug on the DCUYellow ConnectorControl PanelA Black connector(connects to thewaterfall lights) Photocell sensorExterior lights ATemperature sensor K7 K8 K2K3K4K5K6 Page 48 ELITE SERIES ELITE SERIES Export Circuit diagram This wiring diagram is used for Export 230 VAC (50 Hz) dedicated power models. Stereo(Optional) Power Supply StandardOzonatorO 3 GRNTB1 230 VAC 3-Wire Connection (50Hz, USE COPPER CONDUCTORS ONLY. WIRE SIZE MUST BE APPROPRIATE PER NEC AND/OR LOCAL CODESBLU BLUJ6 BRNJ5 BRNBRNBLUBLKBLUBLUBRNBLUBRN BLU BLUBRN BRN BRN 21 Flow switchHi - limit / freeze sensorTemperature sensor J1 J2J3 F120A, 250VSC-20 Pump 1Pump 2 Transformer230 VACJ4F1 JP142 31 6 5 8 7 HIHILO C Control Panel Circ.Pump J20 K1J21J11J12J13J14J15J16J17J18J19 J7 J8 J9 J10 Heater2.7 kW @230 VAC Blue wires 12 VACconstant voltage(connects to theyellow wires onthe transformer) LightDCU Waterfall, Accessories, Air Contols and Footwelllights can connect to anyplug on the DCUYellow ConnectorControl PanelA Black connector(connects to thewaterfall lights) Photocell sensorExterior lights A K5K6 K7 K8 K2K3K4 Page 49 ELITE SERIES ELITE SERIES Optional Stereo Re...