Fabricar: AeroGarden
Tamaño del archivo: 770.67 kb
Nombre del archivo: 353590b2-02e4-4fa9-a7ee-11d08667665a.pdf
|
Resumen del manual
With other hand, support Lamp Hood and use thumb to push in Locking Button. Release Locking Button while pulling up on Lamp Arm. Locking Button will automatically click into next notch. Replace Bowl on Base and plug in AeroGarden 3. 2 1 3 5 4 Raise lamp Hood (light) As plants grow to 1-2” from light, raise Lamp Hood one notch at a time. Be sure Lamp Arm is in the lowest position when starting your AeroGarden 3. note: When lowering Lamp Hood, be sure to hold Lamp Arm to avoid crushing plants. Basic Reminders About Your AeroGarden (continued) Unplug AeroGarden 3 and remove Bowl from Base. Hold Lamp Arm with one hand. With other hand, support Lamp Hood and use thumb to push in Locking Button. Release Locking Button while pulling up on Lamp Arm. Locking Button will automatically click into next notch. Replace Bowl on Base and plug in AeroGarden 3. 2 1 3 5 4 Raise lamp Hood (light) As plants grow to 1-2” from light, raise Lamp Hood one notch at a time. Be sure Lamp Arm is in the lowest position when starting your AeroGarden 3. note: When lowering Lamp Hood, be sure to hold Lamp Arm to avoid crushing plants. 10 Basic Reminders About Your AeroGarden (continued) Basic Reminders About Your AeroGarden (continued) ReplaceBulb When “Replace Bulb” light on control Panel illuminates after 6 months of use… • Unplug AeroGarden 3 about the time your light comes on. • Remove old Grow Bulb and carefully discard*. IMPORTANT: To avoid burning, be sure Grow Bulb is cool before handling. • Insert new Grow Bulb into Lamp Hood. • Plug in AeroGarden 3 and press and hold “Reset” button until “Replace Bulb” light blinks (3 seconds). Release “Reset” button, then press and release again. “Replace Bulb” light will go off and timer is now reset. Early Grow Bulb Replacement If you replace Grow Bulb before “Replace Bulb” light illuminates, be sure to restart grow bulb timer as follows: • Press and hold “Reset” button until “Replace Bulb” light blinks – about 9seconds. •Release“Reset”button. • Quickly press and release “Reset” button. “Replace Bulb” light will blinkonce and grow bulb timer will be reset. Replace Grow Bulb – order bulbs at * Check with local recycling authorities for light bulb recycling availability in your area. need AddITIonAl HelP? For supplies and information, visit… 11 cleaning Instructions for your AeroGarden Use only water and mild soap when cleaning your AeroGarden (except when Sanitizing - Step 6). Do not use abrasive cleaners or run through the dishwasher. When your garden has completed its growing cycle… • Clean water level indicator Prism (located in Bowl), using a soft cloth. – Grasp rubber piece holding Prism in place and gently slide it up and out of Bowl. – Using tap water, wipe off Prism and rinse well. – Gently slide Prism back into housing in Bowl. •Usingremainingsanitizingwater, wipe out Bowl, then empty. Rinse Bowl with tap water. Repeat. Towel dry Bowl and Grow Surface before putting them back together and setting them on Base. If Grow Bulb has been in use more than 6 months, it should be replaced at this time (see page 11). Your AeroGarden is now ready for replanting. Unplug AeroGarden. Carefully remove Bowl and Grow Surface from Base and bring to a sink. Set Base and Lamp Hood aside. NEVER SUBMERSE BASE AND CONTROL PANEL IN WATER. Remove Grow Surface from Bowl and place on counter near a sink. Empty contents of Bowl in sink. Remove Seed Pods and plants from Grow Surface. • Pull Seed Pods out of Grow Surface openings. • Throw away Seed Pods and plant debris (plant growth and roots). If you compost, plant debris can be composted. Sanitize AeroGarden.* • Fill Bowl . full with water. • Add 1/8 cup (24ml) of chlorine bleach. • Let sit for 2 minutes. • Using sanitizing water, wipe Grow Surface with soft cloth or sponge. Scrub underside of Grow Surface with soft scrub brush to remove any tangled roots. • Thoroughly rinse Grow Surface with tap water and set aside. 1 2 3 4 5 6 9 7 8 Prepare For Your Next Garden Plant Growth Seed Pod Grow Surface Roots Prism *Gloves recommended. cleaning Instructions for your AeroGarden Use only water and mild soap when cleaning your AeroGarden (except when Sanitizing - Step 6). Do not use abrasive cleaners or run through the dishwasher. When your garden has completed its growing cycle… • Clean water level indicator Prism (located in Bowl), using a soft cloth. – Grasp rubber piece holding Prism in place and gently slide it up and out of Bowl. – Using tap water, wipe off Prism and rinse well. – Gently slide Prism back into housing in Bowl. •Usingremainingsanitizingwater, wipe out Bowl, then empty. Rinse Bowl with tap water. Repeat. Towel dry Bowl and Grow Surface before putting them back together and setting them on Base. If Grow Bulb has been in us...
Otros modelos de este manual:Otros accesorios para la casa - AeroGarden 100302-WHT (770.67 kb)
Otros accesorios para la casa - AeroGarden 100302-BSS (770.67 kb)
Otros accesorios para la casa - AeroGarden 100302-RED (770.67 kb)
Otros accesorios para la casa - AeroGarden 100302-SLR (770.67 kb)