Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Dometic Corporation 13128 State Rt. 226, P.O. Box 38 Big Prairie, OH 44611-0038 USA 330-496-3211 1-800-321-9886 • Fax: 330-496-3097 ® Registered; ™ Trademark of Dometic Corporation © Dometic Corporation TABLE OF CONTENTS Toilet Model Identification ......................................2 Toilet Dimensions ..................................................3 Installation Instructions.....................................3 - 6 Toilet Operation ..................................................... 6 Proper Cleaning and Maintenance .........................7 Winterizing ............................................................ 7 Spare Parts ........................................................... 7 Deodorants and Special Tissue .............................8 Flush Mechanism Components .............................9 Troubleshooting ................................................... 10 Parts List ............................................................ 11 Wiring Diagram ................................................... 11 Ordering Parts ..................................................... 12 Customer Service ................................................ 12 Three-Year and Ten-Year Limited Warranties ....... 12 WARNING – ELECTRICAL SYSTEM. Turn off electrical power before servicing. Failure to follow these precautions may result in damage to the toilet. 1. Read and understand the complete contents of this manual before operating or servicing the toilet. 2. Do not use drain openers, alcohol, solvents, etc. in the toilet. 3. Do not dispose of sanitary napkins or other non-dissolving items in the toilet, such as facial tissues or paper towels. These items can cause plugging of the toilet. 4. Make sure all guests understand operation of the toilet. TOILET MODEL IDENTIFICATION The model identification label is located on the inside wall of the toilet under the access cover. It will show the DOMETIC CORPORATION model number and serial number. P.O. BOX 38, 13128 STATE RT 226 (800) 321-9886 BIG PRAIRIE, OH 44611 USA MODEL NO. 000 SERIAL NUMBER 000000 Concerto is a trademark, and SeaLand is a registered trademark of Dometic Corporation. 2 CONCERTOTM TOILET DIMENSIONS MODEL 3210 Dimensions may vary ±3/8-inch (13mm). INSTALLATION INSTRUCTIONS System Requirements: • 2 GPM (10.6 lpm) or larger water pump. • 1/2-inch (12.7 mm) water line terminating in 1/2-inch MPT fitting (to connect to toilet water supply hose). • 4-bolt floor (closet) flange. SeaLand flanges available include 3-inch spigot, socket, MPT, or 45-degree swivel socket. • 12 VDC through 2-amp fuse or circuit breaker. Use 14-gauge stranded copper wire. STEP 1: Carefully unpack the toilet bowl, rear access lid and floor flange adapter. CAUTION: HANDLE THE VITREOUS CHINA TOILET AND ACCESS LID WITH CARE. SET THE LID IN AN AREA WHERE IT CANNOT BE BROKEN. PLACE LID ON TOILET ONLY AFTER TOILET INSTALLATION IS COMPLETE. STEP 2: Position the china bowl in the space intended. Confirm that adequate clearance is available for using the flush handle and opening the seat and lid. STEP 3: Mark the floor at the rear corners of the toilet bowl (fig. 1). Measure the distance between the two marks and divide by 2 to find the toilet centerline. Mark the floor at the rear wall for the centerline. STEP 4: Place a carpenter’s square against the back wall, and draw a center line on the floor at least 14 inches (356 mm) long (fig. 2). Mark the centerline for the floor flange at 11-1/4 inches (286 mm) from the wall (fig. 3). Fig. 2Fig. 1 Fig. 3 3 STEP 5a: For through-the-floor water line and electrical wires, mark another centerline 6 inches (152 mm) from the back wall (fig. 4). Fig. 4 STEP 5b: For through-the-wall water line and electrical wires, mark a centerline 8 inches (203 mm) up from the floor centerline (fig. 5). Fig. 5 STEP 6: Make a 4-3/4 inch (121 mm) diameter hole (for most floor flanges) or a 5-1/8 inch (130 mm) diameter hole (for swivel joint floor flange) at the centerline mark furthest from the wall. Make a 1 inch (25 mm) hole at the mark closer to the wall for the water line and electrical wires (fig. 6). Fig. 6 IMPORTANT: The prefered installation method is to mount the floor fIange directly on the finished floor. However, if the bottom of floor flange and bottom of china toilet must be mounted at different heights, the floor flange must be mounted within 3/8 inch (10 mm) of the bottom of the toilet (see illustrations in next column) or leakage will result. Below-Floor Installation Above-Floor Installation STEP 7: Insert floor flange into larger hole and secure to the floor with #12x3/4-inch long flat head wood or sheet metal screws (fig.7). Fig. 7 STEP 8: Route 1/2-inch (13mm) PEX tubing through the smaller hole and install a PEX 1/2-inch MPT fitting (fig. 8). NOTE: A water shut-off valve should be installed in the water line to the toilet for maintenance requirements. Fig. 8 4 STEP 9: WITH THE ELECTRICAL POWER OFF, route #14 gauge stranded copper wire from...