Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
You may want to enclose the spa with a fence and self-latching gate to prevent unauthorized use. 8. Be sure that there is room around the spa to permit servicing of the unit. The dimensions of the spa are 84” W x 84” L x 39” H. You should allow for this size when choosing the location. 9. The spa is not designed to be installed below ground level. However, it is compatible with a deck system that is built flush with the top of the spa, provided you leave access to the motor for service. 10.Be sure to note any other considerations, such as aesthetics or privacy concerns, that may affect the safety or enjoyment of using the spa. 7 Assembly Before beginning assembly, carefully read the following information and instructions: • Place all parts in a cleared area and remove the packing materials from the spa shell. Do not dis- pose of the packing materials until assembly is completed and the spa is operating. • During assembly, make sure that all parts are oriented as shown in the drawings. • Read each assembly step before you begin. • Tighten all parts as you assemble them, unless instructed to do otherwise. ASSEMBLY REQUIRES THE FOLLOWING TOOLS (not included): • One phillips screwdriver A wire connector is provided on the electronics pack of the spa to connect a minimum No. 6 AWG (13.3 mm2) solid copper conductor between the spa and any metal equipment, electrical enclosure made of metal, metal water pipes, or conduit within five feet of the spa. 1. Before beginning assembly, make sure that you have read and understand the information in the box above and on the previous two pages. Remove the four #10 x 2” Sheet Metal Screws (46) that secure the indicated Access Panel (25) to the spa. Carefully remove the Access Panel and set it aside. Be careful not to damage the spa shell. 1 Spa Shell 46 25 46 2. Close the valve knob on the drain hose. Thread the cap onto the drain hose. Locate the four gate valves inside the access opening (there are two gate valves per pump). Make sure that the gate valves are open and that the locking clips are snapped onto the stems of the gate valves, as shown in the inset drawing. Make sure that the six collars are tightened (there are two collars per pump and two on the heater). Refer to step 1. Re-attach the Access Panel (25) to the spa. Collars Cap Valve Knob 2 Gate Valves Locking Clip 8 3. Insert the pillow (47) into the lounge seat recepta3 cle. Rotate the pillow 180. to change its position. 47 4. The hydrotherapy spa operates on a 240-volt power source and must be wired directly to a 40 amp ground fault circuit interrupter (GFCI) installed in your home. This procedure must be performed by a qualified electrician. A wiring diagram is found on the inside of the electronics pack as a reference. Under no circumstances should the spa be wired by someone other than a qualified electrician. Before you have the spa wired, make sure that it is in the position you want and that it can be easily serviced, if needed. 5. Make sure that a qualified electrician has wired the spa to a 240-volt power source. Remove the two warning decals (see page 5) from the spa shell. Using a damp cloth, wipe the spa shell clean. Before filling the spa, make sure that it is in the desired position and that there is room to easily service it. Once the spa is filled, it will have to be drained before it can be moved. Insert a garden hose into one of the filter housings, begin filling the spa. Do not use soft water. The spa may be filled with cold water; however, if warm or hot water is used, the spa will be ready for use sooner. Fill the spa until the water is at the level shown at the right. Do not overfill the spa. Refer to the inset drawing. Set the Filters (5) into the filter housings. Next, screw the Filter Covers (3) into the filter housings until they are fully seated. 6. Pull down one of the straps on the Spa Cover (11) and hold the Buckle (26) against one of the premium cedar panels on the spa. (Note: To position the Buckle correctly, have a second person hold the strap on the opposite side of the Spa Cover snug.) The Spa Cover must be snug. Do not place the Buckle over the grooves between the premium cedar panels. Refer to the inset drawing. Remove the latch from the Buckle (26). Attach the Buckle to the premium cedar panel with two #4 x 3/4” Screws (27). Attach the other three Buckles (26) to the premium cedar panels in the same way. Remove the Spa Cover (11) from the spa. 5 Fill to Here Garden Hose 6 11 26 Strap Strap Latch 26 27 3 5 9 Using the Hydrotherapy Spa The hydrotherapy spa is designed to seat seven adults. The spa holds approximately 375 gallons of water and offers a heating system (80°F to 104°F), a filtration system, and adjustable hydrotherapy jets. Follow the guidelines below to use and maintain the spa for your long-term enjoyment. WIRING THE HYDROTHERAPY SPA The hydrotherapy spa is designed to operate with a 240-volt power source. It must be wired directly into a grounded circuit with a...
Otros modelos de este manual:Otros accesorios para la casa - IMSG63910 (563.95 kb)