Votos - 4, Puntuación media: 4.8
(
)
)
|
Resumen del manual
WARNING The combined weight of the TV/monitor and all attached components and equipment placed on a Chief Wall Plate must not exceed 150 lbs. (68.0 kg), the maximum support weight of the CTA-2536. WARNING Watch for pinch points. Do not put your fingers between movable parts. CAUTION Check the unit for shipping damage before you begin the installation. PARTS 10 40 30 50 60 20 70 Figure 1. CTA-2536 Parts Installation Instructions CTA-2536 CONTENTS PARTS ..............................................................................2 INSPECT THE UNIT BEFORE INSTALLING..............3 TOOLS REQUIRED FOR INSTALLATION..................3 INSTRUCTIONS..............................................................4 Determine a Suitable Mounting Location .....................4 Installing the Wall Plate................................................4 Attaching Wall Arm to Wall Plate ................................5 Attaching Front Cover...................................................5 Connecting NPT Pipe or Nipple to Wall Arm...............5 INSPECT THE UNIT BEFORE INSTALLING Unpack the carton. Carefully inspect the parts for shipping damage. Verify contents listed in Table 1. If you are missing any of the listed parts, contact Customer Service at: 1-800/582-6480.300. Table 1. Shipping Contents ITEM DESCRIPTION QTY 10 Wall Plate 1 20 5/16 X 2.5” Lag Bolt 6 30 5/16 Flat Washer 6 40 M8 Flat Washer 6 50 M8 Lock Washer 6 60 M8 X 16mm Button Head Cap Screw 6 70 M5 Allen Key 1 TOOLS REQUIRED FOR INSTALLATION The tools required for installation are as follows: • Electric drill and bit set • Stud sensor (mechanical or electronic) • .” box-end wrench or ratchet with .” socket • 13mm box-end wrench or ratchet with 13mm socket • Level NOTE: Other tools may be required depending on your method of installation. Installation Instructions CTA-2536 INSTRUCTIONS STEP 1 Determine a Suitable Mounting Location NOTE: The wall plate (10) must be mounted to wood studs that are 16” apart on center. See Figure 2. 16” 1. Locate the wall plate (10), six lag bolts (20) and six flat washers (30). WARNING It is the installer’s responsibility to verify that the structure to which the mount is anchored will safely support five times the combined load of all attached components and equipment. 2. Determine a suitable mounting location. Keep in mind that the wall plate (10) must be mounted to wood studs that are 16” apart on center. 3. Using a stud sensor, locate the two wood studs where you will mount the wall plate (10). STEP 2 Installing the Wall Plate 1. Holding the wall plate (10) against the wall, use a pencil, awl, or small nail to mark the mounting holes where the top two pilot holes will be drilled into the center of the wood studs. Make sure that the mounting holes in the unit are level. 2. Using a 15/64” drill bit, drill two pilot holes for anchoring the wall plate (10). See Figure 2. 3. Using two 5/16” lag bolts (20) and two 5/16” flat washers (30), fasten the wall plate (10) to the wall. See Figure 2. 4. Repeat step 2 to drill four more pilot holes into the wood studs for the middle and bottom mounting holes. 5. Repeat step 3 to install the remaining four 5/16” lag bolts (20) and four 5/16” flat washers (30) into the wood studs and to secure the wall plate (10). Figure 2. Install the Wall Plate Installation Instructions CTA-2536 STEP 3 Attaching Wall Arm to Wall Plate 1. Locate the wall arm, six M8 flat washers (40), six M8 lock washers (50), and six M8 x 16mm button head screws (60). See Figure 3. 2. Attach wall arm to wall plate (10) as follows: a. Using the parts (40, 50, and 60) described in step 1 in the top mounting holes, attach the wall arm to the wall plate (10). b. Using the parts (40, 50, and 60) described in step 1 in the bottom mounting holes, attach the wall arm to the wall plate (10). c. Using the M5 Allen key (70), tighten the six M8 x 16mm button head screws (60) to secure the wall arm to the wall plate (10). STEP 4 [REFERENCE ONLY] Attaching Front Cover 1. Locate front cover and four M4 x 8mm Phillips head cap screws (shipped with wall arm). NOTES • The front cover may be partially removed and reinstalled to conceal power/audio/video cables after the TV/Mount is installed. • You may remove one or both knockouts on cover to assist routing to wall through cover. 2. Install the front cover using four M4 8mm Phillips head cap screws. See Figure 4. STEP 5 [REFERENCE ONLY] Connecting NPT Pipe or Nipple to Wall Arm 1. Locate M6 x 6mm set screw and 1-1/2” NPT pipe or nipple (supplied with TV Mount or purchased separately). 2. Connect the 1-1/2” NPT pipe or nipple (supplied with TV Mount or purchased separately) to the wall arm. See Figure 5. 3. Using the M3 Allen key, install the M6 x 6mm set screw. Tighten the set screw. or purchased separately) WARNING Make sure to tighten the M6 x 6mm set screw to prevent equipment damage or personal injury. Figure 3. Attach Wall Arm to Wall Plate Figure 4. Install Cover on Wall Arm (Supplie...