Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
READ AND KEEP FOR REFERENCE. INSTRUCTIONS Pressure Roller Model 243066, Series A . 20 in. (50 cm) heavy-duty extension . 45 swivel adapter . 9 in. (23 cm) roller frame . 1/2 in. (13 mm) nap roller cover 3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure * This maximum pressure is only possible if the roller frame is * completely plugged. The best operating pressure is the lowest pressure that provides an even paint supply to the roller and typically does not exceed 300 psi (2.1 MPa, 21 bar). 9593A Airless spray gun not included GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 COPYRIGHT 2000, GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001 Warnings and Cautions Installation Assemble the pressure roller as shown in the Parts Drawing on page 3. Pressure Relief Procedure WARNING EQUIPMENT MISUSE HAZARD Misuse can cause the equipment to rupture or malfunction and result in serious injury. To help prevent injury . Do not modify the extension tube or roller frame or use parts not designed for this equipment. . Do not use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in this or any other pressurized aluminum equipment. Such use could result in a chemical reaction, with the possibility of explosion. INSTRUCTIONS FIRE AND EXPLOSION HAZARD Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury. To help prevent injury from fire or explosion . Provide fresh air ventilation to avoid the buildup of flammable fumes from flushing fluids or the coating being applied. . Keep the application area free of debris, including solvent, rags, and gasoline. FLUID INJECTION HAZARD If high-pressure fluid pierces your skin, the injury might look like “just a cut”. But it is a serious wound. Get immediate medical attention. To help prevent injection . Keep your hands and body away form the roller frame when flushing. High pressure fluid emitted from the holes in the frame could cause an injection injury. . Always relieve pressure before you check or repair leaks and when you turn off pump or stop painting. . Never use components rated less than system Maximum Working Pressure. ELECTROCUTION HAZARD Failure to observe the electrical hazards described below could result in serious injury, including burns or electrocution. To help prevent harmful electrical shock . Avoid contact with power lines. . Follow all grounding instructions in your separate pump and gun instruction manual, and comply with all local, state, and national fire, electrical, and safety regulations. . Use only Graco paint hoses. Preventing Corrosion Damage and Freezing CAUTION Never leave water in the pump, gun, or pressure roller. Doing so could cause corrosion and damage from freezing. For storage, flush the system with Graco Pump Armor or mineral spirits/paint thinner. See Flushing on page 3. WARNING To help prevent injection injuries, follow this procedure whenever you stop painting. psi/MPa/bar 1. Put gun trigger safety in SAFETY ON position. 2. Shut off power to pump. 3. Put pump prime/drain valve (required for pressure relief) in DRAIN position to relieve pressure in system. 4. Put gun trigger safety in SAFETY OFF position, and trigger gun to relieve any pressure in hose. 5. Put gun trigger safety in SAFETY ON position, and keep pump prime/drain valve in DRAIN position until you paint again. Operation 1. Follow pump priming instructions using lowest pressure setting at which pump primes. 2. Put pump prime/drain valve in position that delivers fluid to hose. 3. Disengage gun safety latch, and trigger gun briefly until paint comes to roller. 4. Experiment with triggering gun and rolling paint. NOTE: Trigger...
Otros modelos de este manual:Otras herramientas - 309047 (81.49 kb)
Otras herramientas - 9593A (81.49 kb)