Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
All Rights Reserved. Owners Manual and Safety Instructions Table of Contents A. Introduction . . . . . . . . . . . . . . . . . . . . . . . .1 B. Log Splitter Specification . . . . . . . . . . . . .1 C. Unpacking and Assembly Instructions . .2 D. Service Information . . . . . . . . . . . . . . . . .5 E. Special Safety Information . . . . . . . . . . . .5 1. Safety Decals . . . . . . . . . . . . . . . . . . . . . . . .5 2. Safety Warnings . . . . . . . . . . . . . . . . . . . . . .7 3. Important extension cord information . . . . .8 4. Always disconnect power cord from power source . . . . . . . . . . . . . . . . . . . . . . . . .8 5. Hydraulic Safety . . . . . . . . . . . . . . . . . . . . . .8 F. Before You Start Splitting . . . . . . . . . . . .9 G. Operation . . . . . . . . . . . . . . . . . . . . . . . . .11 H. Removal of logs jammed on the wedge . . .12 I. How to change the hydraulic oil . . . . . .13 J. Sharpening the wedge . . . . . . . . . . . . . . .14 K.Transport . . . . . . . . . . . . . . . . . . . . . . . . .15 L. Maintenance . . . . . . . . . . . . . . . . . . . . . .15 M.Troubleshooting . . . . . . . . . . . . . . . . . . . .17 N. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . .17 O. Exploded View and Parts List . . . . . . . .18 P. Mantis Warranty Policy . . . . . . . . . . . . .20 A. Introduction The SwiftSplit log splitter is designed for residential (noncommercial) use and makes your job less physically demanding, more efficient and safer. With a log splitter, the log is split when pressed against a fixed splitting wedge by a pressure plate. Major Components, Controls, and Features Overview: An electric motor assembly provides the power for the system. The motor is connected to a hydraulic oil pump that creates a flow of high-pressure oil which runs to a solenoid valve. A switch set and the solenoid valve let the operator actuate the hydraulic cylinder to split a log. An internal reservoir holds the hydraulic oil that feeds the pump. The hydraulic assembly is attached to the wheel frame assembly, making it easy to move the log splitter around with no lifting. The frame is equipped with folding handles for storage, pivoting support for stability and cord storage hooks for convenience. This log splitter is designed with two hand operating controls (two normally open switches) for safety. The electrical motor is protected by a 15 amp circuit breaker and the pressure relief valve protects the hydraulic assembly in case a log gets jammed. If this happens, after about 5 seconds, the pressure plate slowly travels down to the original position and can be immediately re-activated. B. Log Splitter Specification for Model #5000 Maximum Output Force 10 000 lbs (5 tons) Total Stroke (in)- Ram Travel 15” Total Weight 136 lbs (61.7 Kg) L x W x H 40” L x 20” W x 38” H Voltage 120V Motor 1.5 kW Motor RPM Max 3340 RPM Maximum Log Length 20” (520mm) Recomd. Maximum Log Diameter 12” Dia. Wheel Size 10” Dia. Wedge Vertical Beam Log Guides Pressure Plate Two Switches Folding Handle Wheel Frame Assembly Cord Storage Hooks Connecting Link Stabilizing Bar / Pivoting Support 2 C. Unpacking and Assembly Instructions 1. Cut bands; remove cover and two inserts supporting the top and the bottom of the unit. 2. Put log splitter with the cardboard part’s box in the vertical position by holding the top of the beam and carefully lifting the top of the log splitter until it can stand. Top of the Beam Handle Inserts Cardboard Part’s Box 3. Remove handle from the box first and place it on the floor. 3 4. Remove and open box that is packaged between the log splitter cart and the vertical beam. 5. Remove pivoting support from the box. Also remove wheels and hardware bag. 9 14 11 8 3 28 29 30 111 31 7 KNOB CABLE TIE 152MM (6") LONG 2 510501 2 1 1 2 2 510146 510543 510144 510524 WHEEL SHAFT M14 WHEEL NUT ALLEN WRENCH 6MM ALLEN WRENCH 8MM (DRAIN PLUG) 2 2 4 2 2 510508 510509 510503 510104 510507 BOLT HEX M6 x 30mm CONNECTING LINK NUT LOCK M6, NYLON INSERT WASHER FLAT y6 BOLT HEX M6 x 40mm 2 2 510500 M10 CARRIAGE BOLT,SQUARE NECK, 60mm LONG 510147 ITEM NO. QTY PART NO. DESCRIPTION 4 6. Folding Handle: Install the folding handle onto the frame using knobs (P/N 510501) and carriage bolts (P/N 510500). To do this, align square opening of the folding handle with the frame’s round hole and insert carriage bolt through. Secure it with the handle knob. Repeat the same steps for the opposite side of the handle and tighten the knobs. 7. Use cable ties (P/N 510147) to secure the power cord in place. 8. Installing Wheels: Insert the Wheel Shaft (P/N 510144) in the hub of the Wheel and secure it with the Nut (P/N 510524) provided. Slide the opposite side of the Wheel Shaft through the opening in the frame and bracket, then screw, it into the welded nut. Start by hand and then use a wrench and secure the wheel. Repeat these steps to install the second wheel. 9. Pivoting Support Installation: Align mounting hole of the Pivoting Supp...