Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Arc Welding Safety Warnings and Precautions Warning:This product, when used for welding and similar applications, produces chemicals known to the State of California to cause cancer and birth defects (or other reproductive harm). California Health & Safety Code 25249.5, et seq. 1. Avoid electrical shock. Do not permit electrically live parts, cables, or electrodes to contact skin, clothing, or gloves. Protective clothing should be free of holes, dry, and ANSI approved. This unit draws enough current to cause serious injury or death. Before turning the welder on, check the electrode holder to be sure that there are no protruding screw heads, and that all insulation is secure. Do not weld unless you are insulated from ground and the work piece. 2. Avoid breathing fumes or gases. They can cause serious health problems. Use an active ventilation system directly above the welding area. Keep your head out of the fumes. Inhalation Hazard Welding Produces TOXIC FUMES and GASSES. Exposure to welding gasses can increase the risk of developing certain cancers, such as cancer of the larynx and lung cancer. Also, some diseases that may be linked to exposure to welding gasses or fumes are: • Early onset of Parkinson’s Disease • Heart Disease • Damage to the reproductive organs • Ulcers • Inflammation of the small intestine or stomach • Kidney damage • Respiratory diseases such as emphysema, bronchitis or pneumonia Safety precautions, such as using natural or forced air ventilation and wearing an ANSI approved respirator, are ESSENTIAL to reduce the risk of developing the above illnesses. REV 06/04 SKU 03664 For technical questions, please call 1-800-444-3353. Page 4 Wire Spool (1) not shown Torch Cable and Handle (2) MIG 200 Amp Welder Wire Spool (1) not shown Torch Cable and Handle (2) MIG 200 Amp Welder . Avoid eye and body damage. Arc rays and infrared radiation can injure eyes and burn skin. Wear ANSI approved arc shaded, impact safety full face shield and body protection. Do not allow viewing by visitors without proper eye and body protection. 4. Know proper arc welding practices. Read and understand the manufacturer’s instructions, and well as your employer’s safety practices for arc welding. 5. Connect only to a code approved power source. Connect only to a grounding power source conforming to the National Electrical Code and Local Codes. 6. Avoid fire and explosion. Remove flammable and explosive material from at least 35 feet from the welding arc to prevent welding sparks or molten metal from starting a fire. Keep a type ABC fire extinguisher within easy reach. Thoroughly clean the object being welded of any paint, grease, or other foreign material. 7. Avoid being burned. Always wear ANSI approved welding gear: leather gloves, leather apron, and shoes. Unpacking When unpacking, check to make sure the following parts are included. 220 VAC Power Cord Ground Cable and Clamp (3) If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Assembly 1. Insert the Torch Cable (connection end) into the cable strain relief on the end of the unit. Refer to the photos on the next page. 2. Loosen and unlock the Wire Tension Control. SKU 03664 For technical questions, please call 1-800-444-3353. Page 5 Current Collector (with Wire Routing Housing) Bracket “A” Gas Tube Outlet “B” Square Connector “C” Receptacle “D” Wire Tension Control and Lock Cable Strain Relief Wire Routing Housing Feed Control Wheel Current Collector (with Wire Routing Housing) Bracket “A” Gas Tube Outlet “B” Square Connector “C” Receptacle “D” Wire Tension Control and Lock Cable Strain Relief Wire Routing Housing Feed Control Wheel . Attach the Current Collector (with Wire Routing Housing) to Bracket “A” and tighten. Refer to photos above. 4. Press the white Gas Tube onto the black outlet “B”. 5. Plug the white tube Square Connector “C” into the matching receptacle “D”. 6. Wind (or place) the welding wire onto the Wire Spool (not shown), and mount the Wire Spool onto the Wire Feed Axis Mechanism. See photo on next page. 7. Guide the welding wire into the Wire Routing Housing until it passes the Feed Control Wheel, and into the Torch Cable. 8. Connect a 220 VAC plug (not supplied) to the line cord. This step must be done by a licensed electrician. 9. Plug the line cord into a 220 VAC electrical outlet. 10. Flip the Power Switch on the front of the unit to the ON (I) position. The blower will start. SKU 03664 For technical questions, please call 1-800-444-3353. Page 6 Warning: The Torch Handle is now active. Do not touch anything grounded while performing the next step. Warning: The Torch Handle is now active. Do not touch anything grounded while performing the next step. . While holding the Torch Handle away from any grounding points, press and hold the Trigger Switch to begin feeding the welding wire through the Torch Cable until it reaches the Torch Head. Turn the Wire Feed Speed Con...