Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
5. Attach the Laser to the tripod base. Do this by threading the bolt at the top of the tripod through the holes at the center of the Laser Level’s lower base. 6. Level the Laser by using the tri-brack adjustment screws until the bubbles are centered on the two levels. 7. Push the Pendulum Lock to the right to free the pendulum. See Figure 1. Figure 1 Pendulum Lock 8. Turn on the Laser. Allow the laser lines to stabilize for 4 to 6 seconds before starting any measuring or leveling tasks. 9. To disassemble and store, move the pendulum lock to the left (see Figure 1) and follow the above directions in reverse. NOTICE: If the pendulum lock is not engaged before movement, the level may be damaged. REV 10k Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn Line Buttons off before adjusting Level. 1. After removing the Laser from the Carrying Case, open the battery compartment, insert the two ‘AA’ Batteries into the battery compartment according to the polarity symbols shown inside, and close the battery compartment door. 2. Be sure to set the Laser on as flat a surface as possible. The tri-brack adjustment on the base of the level can be used to help level the unit. (Turn each of the knobs to either raise or lower that corner.) The self-leveling range of the Laser is within ± 6°. Use the 2 Vials on the base to verify that the base is level. Figure 2 Laser OpeningTri.brack (one corner) VialScaleBattery CompartmentPendulum Lock(hidden) 3. Push the Pendulum Lock to the right to free the pendulum. See Figure 1 on page 3. 4. Press the button for the desired line(s) on the top of the unit to switch “ON”. Figure 3 Vertical Line ButtonHorizontal Line Button 5. The Laser Level will work properly if it is positioned within its self-leveling range. 6. Allow 4-6 seconds for the horizontal and vertical Laser lines to be stabilized. After stabilization, the Laser lines can be used for measurement reference. Laser lines may swing slightly due to vibration from surroundings. 7. To prevent damage to the level, tighten the pendulum lock (see Figure 1 on page 3) after use and store in the carrying case. NOTICE: If the pendulum lock is not engaged before movement, the level may be damaged. After Using Laser 1. Detach Laser from Tripod. 2. Switch off both laser lines, horizontal and vertical. Check to see that both indicator LED’s are off. 3. Engage Pendulum Lock by moving it to the left. See Figure 1 on page 3. After use the Pendulum Lock should be locked before the instrument is put away in the Carrying Case. REV 05c, 05g, 07h Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn Line Buttons off before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Installing and Removing Batteries 1. Remove the Battery Cover (see Figure 2 on page 4) and insert two new ‘AA’ Batteries. Follow the polarity symbols so that the positive and negative ends of the batteries match the diagram. 2. WARNING! Do not mix old and new batteries. Remove batteries when storing Laser. Replacement Parts NOTE: Internal replacement parts are not available for this item. Cleaning and Maintenance 1. BEFORE EACH USE, inspect the general condition Laser Level. Check for loose hardware, misalignment or binding of moving parts, cracked or broken parts, and any other condition that may affect its safe operation. 2. AFTER USE, wipe external surfaces of the tool with clean cloth. 3. Store the Laser Level indoors and out of children’s reach. Accuracy Checking NOTE: Due to the complicated, sensitive nature of these procedures, ordinarily only a qualified technician would attempt them. Level Beam Accuracy 1. Set up the instrument with the Tripod centered between two walls approximately 16 ft. apart. Ensure the Rotary Base is level. 2. Push the Pendulum Lock to the right to free the pendulum. See Figure 1 on page 3. 3. Press both the horizontal and vertical buttons to project a laser cross on wall A. Mark point a1 at the intersection of the beams. Turn the cross line laser 180° and repeat on wall B, marking point b1 at the intersection of the beams, see Figure 4. Figure 4 4. Move the instrument straight towards wall A to a point 2 ft. away and repeat step 2, marking the intersections as a2 and b2, see Figure 5. Figure 5 5. a distance (da)=|a1 -a2| b distance (db)=|b1 -b2| If |da - db| <1mm, the accuracy is within tolerance. Otherwise, return the instrument to a qualified technician for repair. REV 07h Horizontal Beam Level Accuracy (End to End) 1. Set up the instrument with the Tr...