Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 1999 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions or replacement parts, please call 1-800-444-3353. THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s record below: Model Serial No. Purchase Date SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly. Technical Specifications Tool Name: Log Splitter-10 Ton Horizontal Item Number: 39981 Capacity: 10 Ton Ram Diameter: 1.572” Ram Travel: 7” Minimum Log Capacity: 15-1/2” Long Maximum Log Capacity: 18-1/2” Long Maximum Log Diameter: 6-1/2” Weight: 100 Lbs. Overall Length: 12-1/8” Overall Width: 7-1/4” Overall Height: 43” Handle Length: 29-1/2” Warning: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that COMMON SENSE AND CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO THIS PRODUCT, BUT MUST BE SUPPLIED BY THE OPERATOR. The Operator PLEASE REMEMBER: Do not operate the product if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment/reflexes might be impaired. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective gloves and non-skid footwear is recommended. Wear restrictive hair covering to contain long hair. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Maintain proper footing and balance at all times. #39981 Page 2 Work Area TO AVOID RISK OF PERSONAL INJURY, EQUIPMENT DAMAGE, FIRE AND SHOCK, MAKE SURE YOUR WORK AREA IS: Free of damp, wet or rainy conditions. Free of children (never let them handle tools or machinery). Well-lit. Clean and uncluttered. Before Operating Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Before operating your Log Splitter check for damaged parts. You should also: Make sure all clamps, locks and bolts are tight. Keep Guards in place and in working order. Assembly Your Log Splitter requires some limited assembly. Please refer to Figure 1, and to the Assembly Diagram on page 7 and Parts List on page 6 as needed for assembly and operation. Unpack the Log Splitter at the place that you will be using it. The Log Splitter is heavy, so be certain to use proper lifting techniques when moving and placing the Log Splitter. To complete the assembly, insert each Handle (A-16) into each Socket (A-25) as shown in Figure 1. Your Log Splitter will then be ready to operate. Handle (A-16) Log Splitter Assembly Socket (A-25) Figure 1-Operating Handle Instruction #39981 Page 3 Rev 08l Operation Never force the tool or attachment to do the work of a larger industrial tool. It is designed to do the job better and more safely at the rate for which it was intended. Step 1) Make certain that the maximum length of each log to be split does not exceed 18-1/2”. If the log exceeds this length, it must be cut to no longer than 18-1/2”. Step 2) Made certain that the Piston Rod (A-32) is fully retracted into the Cylinder (A-36). If not fully retracted, turn the Release Screw (A-44) counterclockwise to release the hydraulic pressure. Once this is completed, and the Piston Rod is fully retracted into the Cylinder, tighten the Release Screw. Step 3) Place the log between the Wedge and the Piston Assembly, resting the log in the metal Cradle. Step 4) Grip one Handle (A-16) in each hand and move them in a back-and-forth motion with one lever being pushed fully forward and one lever being pulled fully rearward. Please see Figure 3 for illustration of this step. Piston Rod (A-32) Release Screw (A-44) Figure 2-Retracting the Piston Rod Warning: When splitting wood, make sure the area around the Wedge and Piston Assembly is clear of people to avoid the possibility of injury from falling wood pieces. Never let children use the Log Splitter. Keep children away from the work area at all times. Operating Lever Piston Rod (A-32) Figure 3-Operation of the Log Splitter #39981 Page 4 Rev 08l Step 5) Repeat Step 4 to advance the Piston Rod (A-32) forward. This will push the log against the Wedge and split the log. Step 6) Once the Log is split, remove the pieces from the Log Splitter. Turn the Release Screw counterclockwise so that the Piston retracts back into the Cylinder as in Step 2 (see Figure 2). Tighten the Release Screw onc...