Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
2. Turn prime/spray valve to SPRAY position. 3. Disengage inline valve safety latch, trigger the inline valve, and roll the surface until paint comes to roller. NOTE: Trigger the inline valve briefly only when you need more paint. Determine how often you must trigger the inline valve to maintain an even paint supply to the roller. 4. Increase pump pressure only if triggering inline valve cannot supply enough paint for your rolling speed. Relieve pressure, page 3, whenever you stop painting. 5. Elevate roller end of extension tube to prevent paint from draining out. Flush pump, inline valve, and roller frame immediately after each use to prevent paint from drying in roller frame and damaging it. Cleaning the EvenFlow Roller Frame 1. Relieve pressure, page 3. 2. Remove roller cover (19) and diffuser (23) from roller frame as follows (see Parts Drawing): a. Using your thumb, press down on clip (5) to release end caps (2 &4), diffuser (23) and roller cover (19) into a pail. b. Remove roller cover (19) from diffuser (23). c. Pull end caps (2 & 4) off diffuser (23). 3. Clean roller cover (19), caps (2 & 4) and diffuser (19) with water or a compatible fluid for oil–based materials. 4. Place roller frame (1) in paint pail. Be sure the holes in roller frame (1) are facing inside the paint pail. 4 309445 5. Prime pump with water or flushing fluid for oil– based materials. Use the lowest pump priming pressure setting. 6. Turn prime/spray valve to SPRAY. NOTE: Perform Step 7 at the lowest pressure possible. 7. Trigger inline valve until flushing fluid begins to dilute the paint. 8. Place roller frame (1) in another bucket and continue flushing until fluid coming out of the roller frame (1) is clear. Cleaning Contractor Inline Valve Relieve pressure, page 3. 1. 2. Push up on bottom of trigger guard and swing it away from trigger. 3. Unscrew inline valve handle from housing. Remove filter and clean it in compatible solvent. NOTE: Do not soak entire inline valve in solvent. Prolonged exposure to solvent can ruin packings. 4. Apply lithium–based grease to threads of inline valve handle and reassemble inline valve. Storage If you are going to store the airless equipment for an extended period of time after flushing with water-base fluid, flush again with Graco Pump Armor or mineral spirits/paint thinner. Leave this fluid in the system during storage. 309445 5 Notes 309445 Parts List 1 5 12 19 2 4 23 ti10642a 14 7 Pressure Roller Additional Roller Covers The following pressure roller covers are available at your local distributor: 107589 9 in. (23 cm); 3/8 in. (9.5 mm) nap 107590 9 in. (23 cm); 1/2 in. (13 mm) nap 107591 9 in. (23 cm); 3/4 in. (19 mm) nap 107592 9 in. (23 cm); 1-1/4 in. (32 mm) nap Model 245397, Series A Ref. No. Part No. Description Qty. 1 244271* FRAME, roller 1 2 245999 CAP, end (includes seal and retainer) 1 4 246277 CAP, end (includes seal, retainer, and o–ring) 1 5 197106 CLIP, roller 1 7 15H622 GASKET 1 12 115524 GASKET 1 14 232122 EXTENSION, 20 in. (50 cm) 1 19 107590 ROLLER, cover, 9 inch, 1/2 in. (13 mm) nap 1 23 15B065 DIFFUSER 2 . Additional Heavy Duty Extensions The following extensions can be mixed and matched to create any length pressure roller needed and are available at your local distributor: 232121 10 in. (25 cm) 232122 20 in. (50 cm) 232123 40 in. (100 cm) 232124 60 in. (150 cm) 232125 80 in. (200 cm) 309445 7 Parts List TI0667 108 119 111 120 107 106 110 103 102 113 112 114 104 105a 105b 105 101 105c 105d 8 309445 Parts List Contractor In–line Valve Model 244161 Ref. No. Part No. Description Qty. 101 218070 NEEDLE–DIFFUSER/SEAT KIT 1 102 244193 TRIGGER, valve, In–line (includes 107) 1 103 196869 GUARD, trigger 1 104 238817 KIT, swivel 1 105. 218131 FLUID FILTER ASSEMBLY 1 (standard 50 mesh) includes replacement parts 5a, 5b, 5c, 5d 105a 179722 RETAINER, spring 1 105b 179731 ELEMENT, strainer 1 105c 179763 SPRING, compression 1 105d 179750 RETAINER, spring 1 106. 179733 SEAL, sleeve 1 Ref. No. Part No. Description Qty. 107 107110 LOCKNUT 1 108 197052 ADAPTER, RAC 1 110 197058 BRACKET, stem 1 111 197568 HOUSING, fluid 1 112 113409 RETAINER, guard 1 113 195788 HANDLE, valve 1 114 104938 PACKING, o–ring 1 119 177538 STUD, trigger 2 120 105334 LOCKNUT 2 . Keep these items on hand to reduce down time. . The Contractor Inline Valve contains a paint filter (218131) inside handle. The primary function of the paint filter is to prevent clogging of spray tips. . The paint filter may be removed for rolling applications. . Remove and...
Otros modelos de este manual:Otras herramientas - 245397 (212.4 kb)
Otras herramientas - Series C (212.4 kb)