Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Rain will cause rust on the inside of the cylinder. 3 I C — I B ASSEMBLY INSTRUCTIONS CONTENTS OF HARDWARE PACK AND LOOSE - PARTS: (See Figure 1) A (1) Handle Grip B (1) Handle C (1) Hairpin Cotter (may be rings) D (1) Clevis Pin (may be pin) E (1) Axle F (2) Push on caps 1/2" Dia. G (2) Spacers H (2) Wheels FIGURE 1 WELDED TUBE WHEEL (H) \ 1. Remove the log splitter, loose parts and literature from carton. Check to be sure all parts are removed from carton before discarding the carton. 2. Place the axle (E) through the welded tube on splitter. See figure 2. 3. Next, place spacers (G) on each side of splitter, over axle. See figure 2. PUSH ON CAP (F) FIGURE 2 HAMMER' FIGURE 3 USE A SECOND HAMMER, OR E LOCK OF WOOD 4. 5. Next, place wheels (H) over each end of axle. See figure 3. Secure wheels to axle with push on caps (F). A hammer and block of wood will be required to hammer on the caps. See figures 2 and 3. 4 5. Lift the handle socket up so that the hole lines up with the hole in plunger shaft. See figure 4. 6. Secure handle socket to plunger shaft with hair pin (C) and clevis pin (D). See figure 4. 7. Place the handle grip (A) over one end of handle (B). Warm soapy water will aid in assembly. Tap grip on. 8. Place handle over handle socket. FIGURE 4 HANDLE ON CYLINDER MOUNTING ASSEMBLY FIGURE 5 OPERATION This 8 ton capacity hydraulic unit is a special design, manufactured for use one log splitter only. 1. This splitter can be adjusted manually for logs 8" to 24" long. There are twelve different settings. Settings are approximately 1-1/2" apart. See figure 5. 2. Simply lift up on handle of cylinder mounting assembly and slide the unit forward or backward for the correct log length. See figure 5. 3. Pull the release valve up and back to lock. Then -- handle can be pumped to split logs. See figure 6. FIGURE 6 5 I Push the release valve down and forward to release pressure. Cylinder will return, with the aid of two return springs. See figure 7 and copy of label below. DOWN TO . UP TO LOCK RELEASE / / I PUMP AND PRESSURE Zz -y SPLIT —' 5052 FIGURE 7 MAINTENANCE CYLINDER RESEIIVOIR SCREW AND WASHER SCREWDRIVER HANDLE HANDLE FIGURE 8 RESERVOIR OIL 1. Lift the handle on the cylinder mounting assembly and pull cylinder assembly all the way back to the last notch. See figure 8. 2. Remove the pump handle. 3. Release the pressure in the cylinder. 4. Tip the log splitter up so it rests on the wheels and handle on cylinder assembly. See figure 8. 5. With a standard screwdriver, remove screw anc washer from cylinder reservoir. See figure 8. If oil is up to hole, do not add any oil. If not, add oil to bring level up to hole. Oil capacity is 10 fluid ounces. Nuto H grade 32, or Exxon L.P. conventional #150 Hydraulic oil. 6 Notes IF YOU WRITE TO US ABOUT THIS ARTICLE OR IF YOU ORDER REPLACEMENT PARTS ALWAYS MENTION THIS MODEL & SERIAL NO MODEL Model 632 8 Model 632 PARTS LIST FOR MODEL 632 LOG SPLITTER ^F. J. PART NO. QUAN. DESCRIPTION NEW PART REF. NO. PART NO. QUAN. DESCRIPTION NEW PART 1 01166 1 Handle Grip 13 732-0466 2 Extension Spring .75" 2 747-0488 1 Handle 3/8" Dia. Rod N O.D. x 10.75" Lg. N 3 HW-66713 1 Handle Socket N 14 710-0820 2 Hex L.-Bolt 3/8-16 x 4 711-0599 1 Clevis Pin (Service .75" Lg.* Only) 15 734-1079 2 Wheel 7.0" x 1.75" 5 HW-66727 2 Pin & Ring Assembly N 16 726-0221 2 1/2" Push Cap 6 HW-66722 2 Link N 17 750-0151 2 Spacer 7 717-0614 1 Hydraulic Pump & 18 738-0584 1 Axle 1/2" Dia. x 12" Cylinder Lg. N 8 781-0050 1 Push Plate Ass'y- N 19 781-0066 1 Tube and Rail Ass y. N 9 710-0925 2 Socket Hd. Bolt 1/2- 20 726-0221 2 1/2" Push Cap 13 x .75" Lg. 21 712-0384 2 Hex Cent. L.-Nut 1/2- 10 781-0057 1 Cylinder Mounting 13 Thd. 11 736-0169 2 L.-Wash. 3/8" I.D.* 22 714-0149 1 Hair Pin Cotter (Service 12 710-0926 Socket Hd. Bolt 3/8- Only) 16 x .75" Lg. .... 753-0389 1 Kit-Seal (See Below) N *For faster service order standard nuts, bolts, and washers locally. If these items cannot be obtained locally, order by part number and size as shown on parts list. REF. NO. DESCRIPTION REF. NO. DESCRIPTION 1 Quad Ring 7 Ball Retainer 2 Cup 8 Ball U<^ Hair Pin Clip 9 Spring Pin Ring 10 Packing 5 Back-Up Washer 11 Ball 6 "0"-Ring 12 Ball Retainer 13 Spring 9 I MTD PRODUCTS INC ...................... YaRD-M3N COMPANY P.O. BOX 36900 • CLEVELAND OHIO 44136...
Otros modelos de este manual:Otras herramientas - 245-632-000 (709.06 kb)