Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Prior to the operation of any firearm in conjunction with the XT-120 make sure that you completely understand all safety precautions and procedures contained in the XT-120 operator’s manual as well as in the manual for your firearm. Failure to follow these precautions may result in damage to property, serious injury or death. 2. Always follow proper safety precautions with any firearm whether or not equipped with the XT-120. 3. Never point a firearm at anything you do not intend to shoot whether or not equipped with the XT-120. 4. When the XT-120 is attached to a firearm, pointing the XT-120 at a person or object will automatically also point the firearm at that person or object. Therefore, never point the XT-120 at anything you do not intend to shoot. The XT-120 produces adequate light levels to illuminate a subject without the need to point directly at the subject. Light from the XT-120 can be safely pointed at a wall, ceiling or floor and the resulting reflected light will be sufficient to identify the object of interest. The XT-120’s light beam can also be adjusted for wide-angle illumination. 5. The XT-120 allows you to operate the ON/OFF switch while your finger is outside the trigger guard. Do not insert your finger inside the trigger guard until prepared to fire the weapon. 6. Before attaching or detaching the XT-120, always make certain the the chamber of your firearm is empty by following the “clearing” procedure detailed in your firearm’s operator’s manual. 7. Before cleaning the XT-120, replacing bulbs or batteries or any other maintenance, remove the XT-120 from the firearm. 8. Do not operate the XT-120 around any flammable or combustible material such as cleaning solvents, paints or gasoline. Do not operate the XT-120 in an environment which may contain flammable gasses such as evapo- rated gasoline. 9. Test the XT-120 periodically, especially after periods of non-use or prior to employment to verify that it is operating properly. 10. The XT-120 requires completely charged batteries for proper operation. Be careful when handling batteries to prevent leakage of harmful chemicals which can damage skin, clothing or the XT-120 itself. To avoid injury, do not expose batteries to excessive heat or allow any material leaked from a battery to come in contact with eyes or skin. Follow instructions from the battery manufacturer regarding the proper handling, storage and disposal of batteries. 11. CAUTION: The bulb in the XT-120 generates intense heat. When switched ON, never place the light on its face (bulb down) or you may cause damage to the XT-120 or the surface on which it is placed. DANGER Avoid Direct Exposure to Laser Radiation Beam Visible Laser Output Power: <5mW Wavelength: 640±40nm Class IIIa Laser Product • Do not look into the laser beam directly or through binoculars or telescopes. • Do not point the laser beam at mirror-like or reflective surfaces. • Do not shine the beam into the eyes of anyone. DANGER LASER RADIATION AVOID DIRECT EYE EXPOSURE Max. Output 5mW, Wavelength:630 Complies with 21 CFR Chapter 1, Model: XT 120 Manufacture: Feb. 2005 Burris Company 331 East 8th Street, Greeley Colorado OFF VIS ILL VIS ILL AVOID EXPOSURELaser radiation is emittedfrom the APERTURE AVOID EXPOSURE Laser radiation is emitted from the APERTURE XT-120 Warning/Aperture/Mode Label For the location of the Laser Warning Label on the unit see the photo at left. WARNING Do not store the XT-120 with batteries installed. CAUTION Do not over turn the adjusters. 77 Mounting the XT-120 1. With your “cleared and safe” firearm in either hand, hold the XT-120 in the other hand with the bulb pointing away from your body in the same direction as the weapon muzzle. 2. Raise the XT-120 up and toward the firearm with the grooves of the XT-120 aligned with the firearm grooves. Slide the XT-120 back until the latch engages with an audible “click.” 3. Test the security of the latch by attempting to slide the XT-120 forward. It should remain secure and, if so, is safely mounted. Step1Step29Step1Step29 Latch Bar Dismounting the XT-120 1. Place your hand under the XT-120 with your index finger and thumb on each side of the latch bars. Squeeze the bars with the finger and thumb to disengage the latch bar from the firearm. 2. With the latch bars pressed in, slide the XT-120 forward, down and away from the weapon muzzle until clear of the grooves. CAUTION Never put your hand in front of the muzzle of the firearm. Be sure to push the XT-120 forward, down and away from the muzzle. RockerSwitchModeRockerSwitchMode Operating the Switch The rocker switch has two positions: MOMENTARY and STEADY ON. The rocker switch is part of the backplate and you should not attempt to disassemble. MOMENTARY POSITION Rotate the rocker switch in a clockwise direction to turn the light on in a MOMENTARY position. Release the rocker switch to turn the light off. STEADY-ON POSITION Rotate the rocker switch in a counter-clockwise direction until it clicks...