Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
PT302H CAUTION: Before using this Rotary Tool, read this manual and follow all its Safety Rules and Operating Instructions. Safety Instructions Accessories Assembly Operation Maintenance FANTOM, 178 West Service Road, Champlain, N.Y. 12919 Always have one hand firmly placed on the tool body while operating. Never operate the tool by holding only the tool handle. ! WARNING TABLE OF CONTENTS TABLE OF CONTENTS SECTION PAGE SECTION PAGE Product Specifications …………………. 2 Carton Contents ………………………… 6, 7 Power Tool Safety ..…………………….. 3 Know Your Rotary Tool …………..…...... 8 Rotary Tool Safety .….................…... 4 Assembly & Operation …….…………… 9 – 17 Electrical Requirements & Safety …….. 5 Maintenance …………………………….. 17 Warranty ….....................................……. 18 WARNING ! Some dust created by power sanding, sawing, grinding, drilling and other construction activities containschemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: . Lead from lead-based paints . Crystalline silica from bricks, cement and other masonry products . Arsenic and chromium from chemically treated lumberYour risk from these exposures varies, depending on how often you do this type of work. To reduce yourexposure to these chemicals, work in a well ventilated area and work with approved safety equipment such asthose dust masks that are specially designed to filter out microscopic particles. PRODUCT SPECIFICATIONS To avoid electrical hazards, fire hazards or damage to the rotary tool, use proper circuit protection. This rotary tool is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere time delay fuse or curcuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way. Before using your rotary tool, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury to you or damage to the rotary tool. Motor Rating: 120V., 60Hz. 4.0 A. No Load Speed: 30,000 RPM Weight: 3.75 lbs. 2 Rev. 06/03 POWER TOOL SAFETY POWER TOOL SAFETY GENERAL SAFETY RULES ! WARNING Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fireand/or serious personal injury. WORK AREA Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gassesor dust. Power tools create sparks which may ignite thedust or fumes. Keep bystanders, children and visitors away whileoperating the tool. Distractions can cause you to lose control. ELECTRICAL SAFETY Double insulated tools are equipped with a polarizedplug (one blade is wider than the other). This plug willfit in a polarized plug only one way. If the plug doesnot fit fully in the outlet, reverse the plug. If it still doesnot fit, contact a qualified electrician to install apolarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Avoid body contact with grounded surfaces such aspipes, radiators, ranges and refrigerators. There is increased risk of electric shock if your body is grounded. Don’t expose power tools to rain or wet conditions. Water entering the power tool will increase the risk ofelectric shock. Do not abuse the cord. Never use the cord to carry thetools or pull the plug from an outlet. Keep cord awayfrom heat, oil, sharp edges or moving parts. Replacedamaged cords immediately. Damaged cords increase the risk of electric shock. When operating a power tool outside, use an outdoorextension cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock. PERSONAL SAFETY Stay alert, watch what you are doing and use commonsense when operating a power tool. Do not use the toolwhile tired or under the influence of drugs, alcohol ormedication. A moment of inattention while operatingpower tools may result in serious personal injury. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing and glovesaway from moving parts. Loose clothing, jewelry or longhair can be caught in moving parts. Avoid accidental starting. Be sure switch is OFF beforeplugging in. Carrying tools with your finger on the switchor plugging in tools that have the switch ON invitesaccidents. Remove adjusting keys or wrenches before turning thetool ON. A wrench or key that is left attached to a rotatingpart of the tool may result in personal injury. Do not overreach. Keep proper footing and balance atall times. Proper footing and balance enables bettercontrol of the tool in unexpected situations. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat or hearingprotection must be used for approp...