Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
6. Press the “UP” button on the hand control. 7. Before the patient’s body is lifted from the bed, stop and make sure the sling is secured and patient’s knees are against the knee pad. 8. The patient should be comfortable with the pressure under the arms. If not, adjust the sling and try another loop option to release pressure. 9. Press the “UP” button until the patient’s body is completely left the bed. 10. Transfer to another object can be done at this position without the patient attending a full standing position. 11.Release the brakes, close the base, and pull the lift away from the bed. 12. Lower the patient to the object intended. 13. To lift patient in a standing position, continue to lift until the patient’s knees are locked in a standing position. 14. At the standing position, patient’s knees may move away from the knee pad. 15. Close the base, and pull the lift away from the bed. 16. Lower the patient to the object intended. 17. Reverse the above procedures when lowering the patient to the bed. LF2020/LF2090 Sit-To-Stand Patient Lift Owner’s Manual Lift and Transfer From Chair 1. Fit sling as described in “Fitting Lumex Sit-To-Stand Sling”. 2. Push lift towards patient. Open the base of the lift to go around the chair. Apply the brakes on both rear casters. 3. Position patient’s feet on the foot platform and knees against the knee pad. 4. Attached the sling straps to the hooks. 5. Have the patient’s hands holding the handles. For patients who cannot hold the handles, have them hold their arms around the chest. 6. Press the “UP” button on the hand control. 7. Before the patient’s body is lifted from the chair, stop and make sure the sling is secured and patient’s knees are against the knee pad. 8. The patient should be comfortable with the pressure under the arms. If not, adjust the sling and try another loop option to release pressure. 9. Press the “UP” button until the patient’s body is completely left the chair. 10. Transfer to another object can be done at this position without the patient attending a full standing position. 11.Release the brakes, close the base, and pull the lift away from the chair. 12. Lower the patient to the object intended. 13. To lift patient in a standing position, continue to lift until the patient’s knees are locked in a standing position. 14. At the standing position, patient’s knees may move away from the knee pad. 15. Release the brakes, close the base, and pull the lift away from the chair. 16. Lower the patient to the object intended. 17. Reverse the above procedures when lowering the patient to the chair. LF2020/LF2090 Sit-To-Stand Patient Lift Owner’s Manual CHECKING THE BATTERIES charge the batteries from one green light. 1. Check batteries by pressing the Battery Testing Button (blue circle with a battery sign) on the control box. 2. Batteries are fully charged when all lights on the Battery Indicator are "ON". 3. Charge batteries when Indicator shown only one “GREEN” light. 4. Do not use the lift when no “GREEN” light is shown. Charge the batteries immediately. 5. Replace batteries when frequent charging is needed. (Reorder #: DPL650BAT) CHARGING THE BATTERIES 1. Ensure the power is switched "ON" (the red “RESET” button should be up). 2. Insert charging plug into charging port on the control box. 3. Plug charger to power supply. 4. All lights of battery indicator should be "ON" while charging. 5. It takes approximately 2-3 hours to fully 6. It takes approximately 7-9 hours to fully charge the batteries from the red light. 7. Do not leave the batteries on charging for an extended period of time. This will shorten the life of the batteries. 8. Do not let the batteries run down to the last red light. This could shorten the life of the batteries or damage the batteries. 9. Unplug the charger first before using the lift. THE LF2020/LF2090 SIT-TO-STAND PATIENT LIFT WILL NOT OPERATE WHILE CHARGING. IMPORTANT NOTES ON CHARGING 1. Push lift to charging location and charge the batteries with the charger provided. Avoid unplugging hand control and motor from control box. Frequent plugging/unplugging of the hand control and motor into/from the control box could damage the control box. 2. Do not charge batteries over 12 hours. Know What The Battery Indicator Lights Are Telling You Red Amber Green Green Green ON ON ON ON ON FULLY CHARGED ON ON ON OFF OFF NEED CHARGE ON ON/OFF OFF OFF OFF CHARGE IMMEDIATELY. DON’T USE THE LIFT OFF OFF OFF OFF OFF BAD BATTERIES OR BAD CONNECTION Warning Buzzers The control box has a buzzer that provides you with information on the status of the batteries and the lift. To stop the buzzer, push down the RESET button or press the Battery Indicator. BUZZER TYPE INDICATION NOTE 2 beeps/sec Low Battery (red / amber lights on) Charge batteries immediately 3 beeps/sec Low Battery (red light on) Charge batteries immediately 6 beeps/sec Very Low Battery (no light on) Charge batteries immediately 3 beeps every other second Bad Battery (no light on) R...
Otros modelos de este manual:Otros dispositivos personales - LF2090 (242.05 kb)