Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Charging the Batteries with the AC Charger 1 Be sure the engine (if equipped) is turned off. 2 Be sure the batteries are connected before charging the batteries. 3 Open the machine covers. The covers should remain open for the entire charging cycle. 4 Remove the battery vent caps and check the battery acid level. If necessary, add only enough distilled water to cover the plates. Do not overfill prior to the charge cycle. 5 Replace the battery vent caps. 6 Connect the battery charger to a grounded AC circuit. 7 Turn the battery charger on. 8 The charger will automatically shut off when the charging cycle is complete. 9 Check the battery acid level when the charging cycle is complete. Replenish with distilled water to the bottom of the fill tube. Do not overfill. Genie TZ-50 Part No. 114164 Second Edition • First Printing Operator's Manual Transport and Lifting Instructions Observe and Obey: Genie Industries provides this securement information as a recommendation. Drivers are solely responsible for making sure machines are properly secured and the correct trailer is selected pursuant to US Department of Transportation regulations, other localized regulations, and their company policy. Genie customers needing to containerize any lift or Genie product should source a qualified freight forwarder with expertise in preparing, loading and securing construction and lifting equipment for international shipment. Only qualified aerial lift operators should move the machine on or off the truck. The transport vehicle must be parked on a level surface. The transport vehicle must be secured to prevent rolling while the machine is being loaded. Be sure the vehicle capacity, loading surfaces and chains or straps are sufficient to withstand the machine weight. Genie lifts are very heavy relative to their size. See the serial plate for the machine weight. See the Decals section for the serial plate location. Do not drive the machine on a slope that exceeds the slope or side slope rating. See Driving on a Slope in the Operating Instructions section. If the slope of the transport vehicle bed exceeds the uphill or downhill maximum slope rating, the machine must be loaded and unloaded using a winch as described. See the Specifications section for the slope ratings. Part No. 114164 Genie TZ-50 30 Genie TZ-50 Part No. 114164 Operator's Manual Second Edition • First Printing Truck bed Securing the Chassis Place a block under the tongue. Secure a strap over the tongue of the machine. Place a block underneath the axle between the two wheels. Use the four tie-down points on the chassis for anchoring down to the transport surface. Use chains or straps of ample load capacity. Use a minimum of 4 chains to secure the chassis. Adjust the rigging to prevent damage to the chains. Securing to Truck or Trailer for Transit Fully lower and retract the boom. Make sure the boom and the mid-pivot rest securely in the mast cradles. Securely latch the boom hold-down latches. Raise all four outriggers to the stowed position. Always chock the machine wheels in preparation for transport. Turn the key switch to the off position and remove the key before transporting. Inspect the entire machine for loose or unsecured items. TRANSPORT AND LIFTING INSTRUCTIONS Second Edition • First Printing Operator's Manual Observe and Obey: Only qualified riggers should rig and lift the machine. Be sure the crane capacity, loading surfaces and straps or lines are sufficient to withstand the machine weight. See the serial plate for the machine weight. Tie-down TRANSPORT AND LIFTING INSTRUCTIONS Lifting Instructions Fully lower and retract the boom. Securely latch the boom hold-down latches. Raise all four outriggers to the stowed position. Remove all loose items on the machine. Determine the center of gravity of your machine using the table and pictures on this page. Measure from one of the lifting points on the tongue end of the machine. Attach the rigging only to the designated lifting points on the machine. Adjust the rigging to prevent damage to the machine and to keep the machine level. Center of Gravity Table X Axis Y Axis ANSI, CSA and Australia 13.5 in 34 cm16 in 41 cm CE 12.4 in 31 cm16 in 41 cm point Lifting point Y axis Chassis Lifting Points (2) Chassis Lifting Points (2) X axis Part No. 114164 Genie TZ-50 Operator's Manual Second Edition • First Printing Decals Inspection for Decals with Words Determine whether the decals on your machine have words or symbols. Use the appropriate inspection to verify that all decals are legible and in place. Part No. Description Quantity Part No. Description Quantity 28158 Label - Unleaded Fuel Only 82479 Danger - General Safety, Ground 1 (models with engines) 1 82505 Danger - Crushing Hazard, Elevated 28161 Warning - Crushing Hazard 5 Components 2 28164 Notice - Hazardous Materials 1 82506 Caution - Foot Crushing Hazard 6 28174 Label - Power to Platform, 230V 2 82558 Warning - Skin Injection Hazard 2 28176 Notice - Missing Ma...