Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
When the original image size is This Screen Menu cannot be operated when “720p larger than the screen size 1024 x 768, this projector enters “Digital (HDTV)”, “1035i (HDTV)”, or “1080i (HDTV)” is zoom +” mode automatically. selected in the PC System Menu (p26). The True and Digital zoom +/– cannot be selected when “480i”, “575i”, “480p”, or “575p” is selected Wide in the PC System Menu (p26). This projector cannot display any resolution higher Provides image to fit wide video aspect ratio (16 : 9) by expanding than 1280 X 1024. If your computer’s screen image width uniformly. This function can be used for providing a resolution is higher than 1280 X 1024, reset the squeezed video signal at 16 : 9. resolution to the lower before connecting to the Digital zoom + When the Digital zoom + is selected, the On-Screen Menu disappears and the message “D. Zoom +” is displayed. Press the SELECT button to expand the image size. And press the Point Up/Down/Left/Right button to pan the image. The Panning function can work only when the image is larger than the screen size. A projected image can be also expanded by pressing the D.ZOOM button on the remote control. Digital zoom – When the Digital zoom – is selected, the On-Screen Menu disappears and the message “D. Zoom –” is displayed. Press the SELECT button to compress the image size. A projected image can be also compressed by pressing the D.ZOOM button on the remote control. projector. . The image data in other than XGA (1024 x 768) is modified to fit the screen size in initial mode. . The panning function may not operate properly if the computer system prepared in the PC Adjust Menu is used. To cancel the Digital Zoom +/– mode, press any button except the D.ZOOM /, SELECT, R-CLICK, and Point button. 32 Video Input Input Source Selection {Video, S-Video, (Y, Pb/Cb, Pr/Cr)} Direct Operation Choose Video by pressing the INPUT button on the top control or the VIDEO button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below. INPUT button Video Computer 1 Computer 2 . VIDEO button Video Menu Operation 1 2 3 Auto Video Press the MENU button and the On-Screen Menu will appear. Press the Point Left/Right button to move the red frame pointer to the Input Menu icon. Press the Point Down button to move the red arrow pointer to Video and then press the SELECT button. The Source Select Menu will appear. Move the pointer to the source that you want to select and then press the SELECT button. When selecting Auto, the projector automatically detects incoming video signal, and adjusts itself to optimize its performance. The projector selects connection in the following order: 1st Y, Pb/Cb, Pr/Cr 2nd S-Video 3rd Video The Y, Pb/Cb, Pr/Cr jacks has priority over the S-VIDEO jack under the condition of connecting both the Y, Pb/Cb, Pr/Cr jacks and the S-VIDEO jack. The S-VIDEO jack has priority over the VIDEO jack under the condition of connecting both the S-VIDEO jack and the VIDEO jack. When video input signal is connected to the VIDEO jack, select Video. . When Monitor out is selected at the Terminal item in the Setting Menu, Computer 2 is not displayed. See “Terminal” item on page 40. Input Menu Move the pointer to Video and press the SELECT button. VIDEO Source Select Menu (VIDEO) Move the pointer to the source that you want to select and press the SELECT button. . When Monitor out is selected at the Terminal item in the Setting Menu, Computer 2 is not displayed. See “Terminal” item on page 40. When video input signal is connected to the S-VIDEO jack, select S-Video. S-Video Y, Pb/Cb, Pr/Cr When video input signal is connected to the Y, Pb/Cb, Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr. NOTE See “Computer Input” on page 25 for a signal compatible with HDCP. 33 Video Input Input Source Selection (RGB Scart 21-Pin) Direct Operation Choose Computer 2 by pressing the INPUT button on the top control or press the COMPUTER 2 button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below. Menu Operation 1 2 Press the MENU button and the On-Screen Menu will appear. Press the Point Left/Right button to move the red frame pointer to the Input Menu icon. Press the Point Down button to move the red arrow pointer to Computer 2 (Only the Computer 1 is displayed when Monitor out is selected in the Setting Menu.), and then press the SELECT button. The Source Select Menu will appear. 3 Move the pointer to the correct input source and then press the SELECT button. When the input source is coming from video equipment connected to the COMPUTER IN 2/MONITOR OUT terminal with a Scart-VGA Cable, select RGB (Scart). Computer 1 Video Computer 2 INPUT button . COMPUTER 2 button Computer 2 . . Computer 2 is not displayed when the COMPUTER IN 2/MONITOR OUT terminal is used as Monitor out. See “Terminal” item on page 40. Input Menu Move the pointer (red arro...
Otros modelos de este manual:Proyectores - LC-XE10 (1.95 mb)