Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
The three marks bellow are the caution labels for the laser beam. CAUTION : Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser Light Window These caution labels are put on the remote control. BEFORE OPERATION VOLUME ON-OFF FOCUSZOOM VIDEOCOMPUTER D.ZOOM MENU MUTE LASER KEYSTONE NO SHOW FREEZE AUTO IMAGE NORMAL LOCK MUTE BUTTON Used to mute sound.(P21) ZOOM BUTTON Used to adjust zoom. (P20) FOCUS BUTTON Used to adjust focus. (P20) NO SHOW BUTTON Used to turn the picture into black image. (P21) AUTO IMAGE BUTTON Use to operate AUTO IMAGE function. (P27) Used to adjust volume. (P21) VOLUME BUTTON D.ZOOM BUTTON Used to turn the projector into DIGITAL ZOOM mode and resize the image. (P28, 29) FREEZE BUTTON Used to freeze the picture. (P21) NORMAL BUTTON Used to reset to normal picture adjustments preset by the factory. (P26, 30) KEYSTONE BUTTON Used to correct the keystone distortion. (P20, 28, 29) Operating Range Point the remote control toward the projector (the Remote Receiver) whenever pressing the buttons. Maximum operating range for the remote control is about 16.4’ (5m) and 60° front and rear of the projector 16.4’ (5 m) 60° 60° 16.4’ (5 m) 1 Remote Control Batteries Installation Remove the battery Slide the batteries into the 2 Replace the compartment compartment lid. compartment. 3 lid. Press the lid down-Two AA size batteries For correct polarity (+ and –), be sure the battery terminals are in contact with the pins in the compartment. ward and slide it. To insure safe operation, please observe the following precautions : Use (2) AA type alkaline batteries. Replace two batteries at the same time. Do not use a new battery with a used battery. Avoid contact with water or liquid. Do not expose the Remote Control Unit to moisture, or heat. Do not drop the remote control unit. If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries. BEFORE OPERATION TOP CONTROLS AND INDICATORS ZOOM BUTTONS Used to turn the projector FOCUS BUTTONS on or off. (P19) Used to select focus adjust. (P20) ZOOM FOCUS VOLUME ON–OFF MENU MODE SELECT AUTO IMAGE NORMAL LAMP READY WARNING TEMP. LAMP REPLACE Used to select zoom adjust. (P20) POWER ON OFF BUTTON LAMP INDICATOR This indicator is dim when the projector is turned on. VOLUME BUTTONS Used to adjust volume. And bright when the (P21) projector is in stand-by mode. MODE BUTTON READY INDICATOR This indicator is lit in green when the projector is ready to be turned on. WARNING TEMP. INDICATOR This indicator flashes red when internal projector temperature is too high. (P33) LAMP REPLACE INDICATOR This indicator turns to yellow when the life of the projection lamp draws to an end. (P34) MENU BUTTON Used to open or close the MENU operation. (P17, 18) Used to select input source either Computer or Video. (P22, 29) SELECT BUTTON Used to execute the item selected. It is also used to expand the image in DIGITAL ZOOM mode. (P28) POINT BUTTONS Used to select an item or adjust the value on the MENU. It is also used to pan the image in DIGITAL ZOOM mode. (P28) NORMAL BUTTON Used to reset to normal picture adjustment preset by factory. (P26, 30) AUTO IMAGE BUTTON Used to operate AUTO IMAGE function. (P27) BEFORE OPERATION OPERATING ON-SCREEN MENU HOW TO OPERATE ON-SCREEN MENU You can control and adjust this projector through the ON-SCREEN MENU. Refer to the following pages to WIRELESS REMOTE CONTROL POINT BUTTON operate each adjustment on the ON-SCREEN MENU. Used to move the Pointer UP/ DOWN/ RIGHT/ LEFT. 1 MOVING THE POINTER Move the pointer (see the NOTE below) by pressing POINT button(s) on the TOP CONTROL or the REMOTE CONTROL. SELECT BUTTON Used to select the item. TOP CONTROL 2 SELECT THE ITEM Select the item by pressing SELECT button. NOTE : Pointer is the icon on the ON-SCREEN Menu to select the item. See the figures on the section "FLOW OF ON-SCREEN MENU" below. FLOW OF ON-SCREEN MENU Display ON-SCREEN MENU 1 1 Press MENU button to display the ON-SCREEN MENU (MENU BAR). The red frame is the POINTER. Select the Item 2 2 Move the POINTER (red frame) to the ITEM ICON that you want to select by pressing POINT RIGHT / LEFT buttons. 3 3 Select the ITEM by pressing SELECT button. The dialog box of the ITEM appears. SELECT Used to select the item. SELECT BUTTON Used to move the Pointer UP/ DOWN/ RIGHT/ LEFT. POINT BUTTONS SELECT BUTTON POINT DOWN BUTTON MENU BAR POINTER (red frame) ITEM ICON POINTER (red frame) MENU POINTER Control and adjust through ON-SCREEN MENU 4 4 Move the POINTER downward by pressing POINT DOWN button. (The shape of the POINTER becomes an arrow.) 5 5 Move the POINTER to the ITEM that you want to adjust and adjust the ITEM by pressing SELECT button. Refer to the following pages for details of respective adjustments. IMAGE MENU Used to adjust the picture image. [Color / Tint / White Balance / Contrast / Brightness/ Sharpness] (Refe...