Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
(Refer to P32) SCREEN MENU Used to set size of image to Normal or Wide. (Refer to P34) GUIDE WINDOW Shows selected item of ONSCREEN MENU. Same function as Menu for PC source. INPUT MENU Used to select input source either Computer or Video. (Refer to P22) SCREEN MENU Used to adjust size of image. [Normal / True / Wide / Digital zoom +/–] (Refer to P29) BASIC OPERATION TURNING ON / OFF PROJECTOR TURNING ON PROJECTOR 1 1 Complete peripheral connections (with Computer, VCR, etc.) before turning on projector. (Refer to "CONNECTING TO PROJECTOR" on pages 11~13 for connecting that equipment.) 2 2 Connect the projector's AC Power Cord into an AC outlet. LAMP Indicator lights RED, and READY Indicator lights GREEN. NOTE : When “On start” function is ON, this projector is turned on automatically by connecting AC Power Cord to an AC outlet. (Refer to pages 35, 36.) 3 3 Press POWER ON-OFF button on Top Control or on Remote Control Unit to ON. LAMP Indicator dims, and Cooling Fans start to operate. Preparation Display appears on a screen and the count-down starts. The signal from PC or Video source appears after 30 seconds. 30 Preparation Display disappears after 30 seconds. TURNING OFF PROJECTOR 1 1 Press POWER ON-OFF button on Top Control or on Remote Control Unit, and a message "Power off?" appears on a screen. 2 2 Press POWER ON-OFF button again to turn off projector. LAMP Indicator lights bright and READY Indicator is turned off. After projector is turned off, Cooling Fans operate (for 90 seconds). During this "Cooling Down" period, this appliance cannot be turned on. 3 3 When the projector has cooled down, READY Indicator lights GREEN again and you can turn the projector on. After cooling down completely, disconnect AC Power Cord. TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF. Power off? Message disappears after 4 seconds. When “Power Management” function is ON, the projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on page 36. When WARNING TEMP. Indicator flashes red, the projector is automatically turned off. Wait at least 5 minutes before turning on projector again. When WARNING TEMP. Indicator continues to flash, follow the procedures below: 1. Press POWER ON-OFF button to turn the projector off and disconnect AC Power Cord from an AC outlet. 2. Check Air Filters for dust accumulation. 3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.) 4. Turn the projector on again. If WARNING TEMP. Indicator should still continue to flash, call Boxlight at 1-800-762-5757 or 360-779-7901. BASIC OPERATION ADJUSTING SCREEN ZOOM ADJUSTMENT 1 1 Press ZOOM button on Top Control or ZOOM / button on 2 2 Remote Control Unit. The message “Zoom” is displayed. Press ZOOM button or POINT UP button to make image larger, and press ZOOM button or POINT DOWN button to make image smaller. Zoom Message disappears after 4 seconds. FOCUS ADJUSTMENT 1 1 Press FOCUS button on Top Control or FOCUS / button on 2 2 Remote Control Unit. The message “Focus” is displayed. Adjust focus of image by pressing FOCUS / button or POINT UP/DOWN button(s) . Focus Message disappears after 4 seconds. KEYSTONE ADJUSTMENT If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment. 1 1 Press KEYSTONE button on Remote Control Unit or select Keystone on SETTING menu. (Refer to page 35.) Keystone dialog box appears. 2 2 Correct keystone distortion by pressing POINT UP/DOWN/LEFT/RIGHT button(s). Press POINT UP button to • Arrows are white in no correction. reduce the upper part of the image, and press POINT DOWN • Arrow(s) of direction being corrected turn(s) red. button to reduce the lower part. Press POINT LEFT button to • Arrow(s) disappear(s) at the maximum reduce the left part, and press POINT RIGHT button to reduce correction. the right part. Reduce the upper width Reduce the lower width Reduce the left part with Reduce the right part with with POINT UP button. with POINT DOWN button. POINT LEFT button. POINT RIGHT button. PICTURE FREEZE FUNCTION Press FREEZE button on Remote Control Unit to freeze the picture on-screen. To cancel FREEZE function, press FREEZE button again or press any other button. BASIC OPERATION NO SHOW FUNCTION Press NO SHOW button on Remote Control Unit to black out the image. To restore to normal, press NO SHOW button again or press any other button. No show Message disappears after 4 seconds. P-TIMER FUNCTION Press P-TIMER button on Remote Control unit. The timer display “00 : 00” appears on the screen and the timer starts to count time (00 : 00 ~ 59 : 59). To stop P-TIMER display, press P-TIMER button. And then, press PTIMER button again to cancel P-TIMER function. SOUND ADJUSTMENT Indicates roughly level of DIRECT OPERATION volume. Volume Press VOLUME (+/–) button(s) on Top Control or on Remote Control Unit to adjust volume. Volume dialog box appears on the screen...