Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
PAGE POWER MENU The POWER indicator will turn to green and the projector Standby Blinking Power On will become ready to use. TIP: *Turning on the projector will instantly cause the Auto Focus function to operate. (> page 22) Steady orange light Blinking green Steady green ) is displayed at the bottom * When the key lock symbol ( light light right of the menu, it means that the Control Panel Lock is turned on. (> page 41) See page 50 for more details. After you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed. NOTE: When no signal is available, a blue or black screen is displayed. When the projector displays a blue or black screen, the projector will automatically switch to the Eco mode. The projector will return to the Normal mode once a signal is connected. POWER STATUS LAMP POWER STATUS LAMP POWER STATUS LAMP NOTE: If you turn on the projector immediately after the lamp is turned off or when the temperature is high, the fans run without displaying an image for some time and then the projector will display the image. CAUTION: The projector cannot be turned off for 60 seconds after the lamp is turned on and while the POWER indicator is blinking green. • Do not turn off the AC power during this period. Doing so could cause premature lamp failure. 17 3. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the nine menu languages. To select a menu language, follow these steps: 1. Use the SELECT or button to select one of the nine languages from the menu. FOCUS SELECT ENTER EXIT MENU UP PAGE OFF POWER ON PIC-MUTE DOWN FOCUS 2. Press the ENTER button to execute the selection. After this has been done, you can proceed to the menu operation. If you want, you can select the menu language later. (> [Language] on page 40) EXIT MENU UP PAGE OFF POWER ON PIC-MUTE DOWN FOCUS ENTER FOCUS SELECT NOTE: Immediately after turning on the projector, screen flicker may occur. This is normal. Wait 3 to 5 minutes until the lamp lighting is stabilized. When the [Lamp mode] is set to [Eco], the LAMP indicator will light green. If one of the following things happens, the projector will not turn on. • If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal components to cool down. • When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp. • If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and then turn on the power. 18 3. Projecting an Image (Basic Operation) Selecting a Source Selecting the computer or video source NOTE: Turn on the computer or VCR connected to the projector. Selecting a source from the Source list Press and quickly release the SOURCE button on the projector cabinet to display the Source list. Each time the SOURCE button is pressed, each source name will be highlighted in sequence. Press the ENTER button or allow 2 seconds to elapse. The selected signal will be displayed. Detecting the Signal Automatically Press and hold the SOURCE button for a minimum of 2 seconds, the projector will search for the next available input source. Using the Remote Control Press any one of the VIDEO, S-VIDEO and COMPUTER buttons. LAMP STATUS POWER SOURCE AUTO ADJ. FOCUS ON/STAND BY SELECT LAMP MODE VOLUME S-VIDEO VIDEO L-CLICK MOUSE R-CLICK AUTO ADJ.COMPUTER HELP FREEZEPICTURE 19 3. Projecting an Image (Basic Operation) Adjusting the Picture Size and Position Place your projector on a flat level surface and ensure that the projector is square to the screen. Lift the front edge of the projector to center the image vertically. * If the projected image does not appear square to the screen then use the Keystone feature for proper adjustment. (> page 25) About Auto Focus Just placing the projector on a flat level surface makes a focused image. (> page 22) About Auto Keystone Correction Adjusting the height of a projected image or changing the projection angle will result in the Auto Keystone function to work to quickly correct the vertical distortion. (> page 23) Move the projector left to center the image horizontally on the screen. 20 21 2 LAMP STATUS POWER SOURCE AUTO ADJ. FOCUS ON/STAND BY SELECT 1 3 3. Projecting an Image (Basic Operation) Adjust the Tilt Foot 1. Lift the front edge of the projector. CAUTION: Do not try to touch the ventilation outlet during Tilt Foot adjustment as it can become heated while the projector is turned on and during its cool down period after it is turned off. 2. Push and hold the Adjustable Tilt Foot Button on the front of the projector to extend the adjustable tilt foot (maximum ...
Otros modelos de este manual:Proyectores - LT30 (2.77 mb)
Proyectores - LT35 (2.77 mb)