Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Select whichever projection method matches the settingup method. (The projection method can be set from the Option menu. Refer to page 37 for details.) DESK/CEILING DESK CEILING FRONT/REAR !l l FRONT ¡1 (Factory default setting) REAR Ji à* ¡1 NOTE: • You will need to purchase the separate ceiling bracket (ET-PK701) when using the ceiling installation method. Projector position x CO Top edge of screen Screen Bottom edge of screen L: Projection distance SH: Image height SW: Image width H1: Distance from center of lens to bottom edge of projected image (SH -r 10) co .................. Screen 20 Projection distances Screen size (4:3) Projection distance (L) Height position (H1) Diagonal length Height (SH) Width (SW) Wide (LW) Telephoto (LT) 0.76 m(3CQ 0.46 m(1 '6”) 0.61 m(2) 1.15 m(3'9) 0.05 m(1-13/16') 1.01 m(40") 0.61 m(2) 0.81 m(2'8) 1.18 m(3'10) 1.51 m(4'11") 0.06 m(2-13/32'} 1.27 m(50") 0.76 m(2'6") 1.02 m{3'4") 1.49 m(4'10) 1.90 m(6'2") 0.08 m(3") 1.52 m(60") 0.91 m(3') 1.22 m{4') 1.80 m(5'10") 2.29 m{7'6) 0.09 m(3-19/32") 1.77 m(70") 1.07 m(3'6‘) 1.42 m(4'8") 2.12 m(6'11") 2.68 m{8'9") 0.11 m(4- 6/32') 2.03 m(80") 1.22 m{4') 1.63 m(5'4") 2.43 m(7'11") 3.08 m{10'1") 0.12 m(4-26/32') 2.28 m(90~) 1.37 m{4'6) 1.83 m(6 ) 2.74 m(8'11”) 3.47 m(11'4’) 0.14 m(5-13/32') 2.54 m(100") 1.52 m{5') 2.03 m(6'8") 3.05 m(10') 3.86 m{127') 0.15 m{6) 3.81 m(150") 2.29 m(7'6”) 3.05 m(10 ) 4.61 m(15'1") 5,83 m(19'1") 0.23 m{9 ) 5.08 m{200") 3.05 m(10 ) 4.06 m(13'4") 6.17 m(20'2) 7.79 m(25'6") 0.31 m(12') 6.35 m(250") 3.81 m(12'6") 5.08 m(16'8') 7.73 m{25'4") 9.75 m(31 '11') 0.38 m(15) 7.62 m(300") 4.57 m(15') 6.10 m(20'} 9.29 m{30'5") 11.72 m(38 '5') 0.46 m(18') Setting-up dimensions which are not given in the above table can be calculated using the formulas below. If the screen size (diagonal) is SD, then the following formula is first used to obtain the screen width (SW). SW = SD x 4 - 5 The value for SW obtained above can then be used with the following functions to calculate the projection distance for the wide lens position (LW) and the projection distance for the telephoto lens position (LT). LW = 1.535 x SW - 0.068 j LT = 1.933 x SW - 0.066 15 For 16:9 aspect ratios, the following formula can be used to calculate the screen width (SW). SW = SDx 16 -/337“ NOTE: • The dimensions in the table above and the values obtained from the above formulas may contain slight errors. • It is recommended that you use the projection distance for the wide lens position (except in cases where the diagonal picture size is 0.762 m [30"]). 27 Preparation Starting to use Turning on the power (T) Remove the lens cover. (2)Connect the accessory power cord to a 100 V-240 V AC (50 Hz/60 Hz) pow^r supply. (3) Press the MAIN POWER switch to the “|” side to turn on the power. The power indicator on the projector will illuminate red. You can check whether a signal is being input or not by checking the status of the RGB INPUT indicator. Refer to page 24. (4) Press the POWER button on the projector or remote control unit. The POWER button on the projector will flash green. After a short period, the button will illuminate green, and a picture will be projected. (5)Turn the focus ring to make broad adjustments to the picture focus. ©Set the projection method, (pages 20 and 37) (7) Press the input select (INPUT, RGB, VIDEO) buttons on the projector or remote control unit to select the input signal. The input signal selected will change as shown in the table below each time an input select button is pressed. RGB1(YPbPr1) —» RGB2(YPbPr2) Projector INPUT T I S-VIDEO <— VIDEO Remote control RGB RGB1 (YPbPrI) <-> RGB2(YPbPr2) unit VIDEO S-VIDEO VIDEO (8)Press the VOLUME +/- buttons on the remote control unit to adjust the volume. Refer to page 25 for details on how to adjust the volume using the buttons on the projector control panel. 22 d) While pressing the adjuster button, adjust the forward/back angle of tilt of the projector. NOTE: • If the projected picture is tilted to the right or left, turn the rear adjuster leg underneath the projector to the left or right. Refer to page 12. ® Press the AUTO SETUP button on the projector or remote control unit. (t£)Turn the zoom knob so that the size of the picture matches the size of the screen. Repeat steps (§) to (M) until the screen and the picture match. ©Turn the focus ring to adjust the picture focus. ©Turn the zoom knob once more so that the size of the picture matches the size of the screen. Turning off the power ©Press and hold the POWER button on the projector or remote control unit for 3 seconds, or press it twice. The lamp unit will switch off and the picture will stop being projected. (The POWER button on the projector will illuminate orange.) (DWait until the POWER button on the projector illuminates red (until the cooling fan stops). Never turn off the MAIN POWER switch, disconnect the p...
Otros modelos de este manual:Proyectores - PTL501U (1.93 mb)
Proyectores - PTL711U (1.93 mb)