Votos - 4, Puntuación media: 3.8
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
Caution Do not cover the air inlet port or the air outlet port. BDoing so may cause the projector to overheat, which can cause fire or damage to the projector. BDo not place the projector in narrow, badly ventilated places such as closets or bookshelves. Do not set up the projector in humid or dusty places or in places where the projector may come into contact with smoke or steam. BUsing the projector under such conditions may result in fire or electric shocks. When disconnecting the power cord, hold the plug, not the cord. BIf the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious electric shocks may result. Always disconnect all cables before moving the projector. BMoving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to occur. Do not place any heavy objects on top of the projector. BFailure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury. ENGLISH-7 Preparation Do not into water BFailure to observe or catch fire, and When inserting the correct. BIf the batteries are inserted injury or contamination of the may result. Use only the specified batteries. BIf incorrect batteries are used, they contamination of the battery compartment result. Do not mix old and new batteries. BIf the batteries are inserted incorrectly, they may injury or contamination of the battery compartment may result. Do not put your weight on this projector. BYou could fall or the projector could break, and injury may BBe especially careful not to let young children stand or sit on Disconnect the power cord plug from the wall outlet as a safety precaution before carrying out any cleaning. BElectric shocks can result if this is not done. Ask an Authorized Service Center to clean inside the projector at least once a year. BIf dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation. BIt is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest Authorized Service Center to clean the projector when required. Please discuss with the Authorized Service Center regarding cleaning costs. We are constantly making efforts to preserve and maintain a clean environment. Please take non repairable units back to your dealer or a recycling company. NOTICE: BThis product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <8-ENGLISH Accessories Check that all projector. PreparationRemote control unit (N2QAEA000025 x1) Video cable [3.0 m (9.10.), K2KA2FA00003 x1] AAA batteries for remote control unit (x2) Power cord (K2CG3FR00001 x 1) Before use Cautions regarding setting-up Avoid setting up in places which are subject to vibration or shocks. The internal parts can be damaged, which may cause malfunctions or accidents. Do not set up the projector near high-voltage power lines or near motors. The projector may be subject to electromagnetic interference. If installing the projector to the ceiling, ask a qualified technician to carry out all installation work. You will need to purchase the separate installation kit (Model No.ET-PKE700). Furthermore, all installation work should only be carried out by a qualified technician. If using this projector at high elevations (above 1 400 m), set the “FAN CONTROL” to “HIGH”. (Refer to page 47.) Failure to observe this may result in malfunctions. ENGLISH-9 ENGLISH-11 Preparation 10-ENGLISH Notes on use In order to get the best picture quality Draw curtains or blinds over any windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen. Do not touch the surfaces of the lens with your bare hands. If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen. Moreover, when not using the projector, retract the lens and then cover it with the lens cover. Screen Do not apply any volatile substances which may cause discoloration to the screen, and do not let it become dirty or damaged. Lamp The lamp may need to be replaced earlier due to variables such as individual lamp characteristics, usage conditions and the installation environment, especially when the projector is subjected to continuous use for more than 10 hours or the power is frequently turned on and off. Liquid crystal panel BDo not project the same image for long periods of time, as this may remain as an afterimage on the liquid crystal panel. BThe liquid crystal panel of the projector is built with very high precision technology to provide fine...