Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
% Press the F FF or G GG button to select “COLOR TEMP.”, and then press the I II or H HH button to select “STANDARD”. NOTE: BsRGB is only enabled when RGB signals are being input (when “ LAMP POWER” is set to “ HIGH” and “ AI” is set to “ OFF”) . ENGLISH-39 Adjusting When an RGB input, press the AUTO button first to initiate positioning. If the optimum is not obtained when “ AUTO SETUP” is carried out, adjust by the following procedure. Press the F or G button on the projector or remote control unit to select an item, and then press the I or H button to change the setting. For items with bar scales, press the ENTER button or the I or H button to display the adjustment screen, and then press the I or H button to make the adjustment. When an RGB/YPBPR signal is being input When an S-VIDEO/VIDEO signal is being input POSITION POSITION DOT CLOCK 32 CLOCK PHASE 16 ASPECT 4:3 RESIZING ON FRAME LOCK OFF STANDARD SELECT ENTER RETRN POSITION POSITION ASPECT 4:3 RESIZING ON STANDARD SELECT ENTER RETRN POSITION Moves the picture Press the ENTER button “ POSITION” screen. Press the I or Hbutton to move the picture horizontally. Press the F or Gbutton to move the picture vertically. POSITION H 64 V 32 DOT CLOCK (RGB only) Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is projected. If this happens, press the I or H button to adjust so that any such noise is minimised. CLOCK PHASE (RGB/YPBPR only) Adjust the “ DOT CLOCK” setting first before carrying out this adjustment. Press the I or H button to adjust so that the noise level is least noticeable. NOTE: BIf signals with a dot clock frequency of 100 MHz or higher are being input, interference may not be completely eliminated when the “ DOT CLOCK” and “ CLOCK PHASE” adjustments are carried out. 40-ENGLISH ASPECT (S-VIDEO/VIDEO/and 576p YPBPR only) ASPECT AUTO [ 4:3 [ 16:9 [ S4:3 AUTO (S-VIDEO only) When an S1 video signal is being input, the aspect ratio is changed automatically to project a 16:9 picture. 4:3 The input signal is projected without change. 16:9 The picture is compressed to a ratio of 16:9 and projected. When a horizontally squeezed signal is being input. [ S4:3 The size of the input compressed to 75% (This is useful for projecting picture with a 4:3 aspect 16:9 screen.) When a 4:3 signal is being input. [ When using the 16:9 screen S1 video signals B S1 video signals are a type of video signal with an aspect ratio of 16:9 which include a detector signal. This detector signal is output by some sources such as wide-vision video decks. B When “ ASPECT” is set to “ AUTO” , the projector recognizes the detector signal and automatically switches the aspect ratio to 16:9. ENGLISH-41 Adjustments and settings NOTE: BIf a selected mode match the aspect ratio input signal, it may affect quality of viewing of the original picture. Keep this in mind when selecting the aspect ratio. BIf using this projector in places such as cafes or hotels to display programs for a commercial purpose or for public presentation, note that if the aspect ratio (16:9) selection function is used to change the aspect ratio of the screen picture, you may be infringing the rights of the original copyright owner for that program under copyright protection laws. BIf a normal (4:3) picture which was not originally intended for wide-screen viewing is projected onto a wide screen, distortion may occur around the edges of the picture, or part of the picture may not be visible. Such programs should be viewed in 4:3 mode to give proper consideration to the aims and intentions of the original program’s creator. Adjustments and settings 42-ENGLISH RESIZING This should normally (This setting is only which have lower resolutions the LCD panels. Refer to for details.) ON The pixel resolution of the input signal is converted to the same resolution as the LCD panels before being projected. For signals with lower resolutions, gaps in the pixels are automatically interpolated into the picture before it is projected. This may sometimes cause problems with the quality of the picture. OFF The input signal is projected at its original resolution, with no pixel conversion. The projected picture will be smaller than normal, so adjust the zoom setting or move the projector forwards or backwards to adjust the picture size if necessary. If set to “OFF”, some features, such as “D.ZOOM” (digital zoom), “KEYSTONE” or “INDEX WINDOW” will not function. FRAME LOCK If the picture’s condition is bad while a RGB moving picture is projected, set “FRAME LOCK” to “ON”. Refer to page 60 for compatible RGB signals. Changing language Press the F or G button on the language, then LANGUAGE ENGLISH ENGLISH DEUTSCH FRANCAIS ESPANOL ITALIANO SELECT ENTER RETRN Option settings Press the F or G button on the projector or remote control unit to select an item, then press the I or H button to change the setting. OPTION2 BACK COLOR BLUE FRONT/REAR FRONT DESK/CEILING DESK FAN CONTROL STANDARD...