Votos - 1, Puntuación media: 5
(
)
)
|
Fotos y especificaciones Sony VPL-CS21 |
Otros manuales para este modelo:
Resumen del manual
c Adjust “Shift” on the Adjust Signal... menu of the Signal menu properly (see page 22). The picture flickers. “Dot Phase” on the Adjust Signal... menu of the Signal menu has not been adjusted properly. c Adjust “Dot Phase” on the Adjust Signal... menu of the Signal menu properly (see page 22). Others Troubleshooting Sound Symptom Cause and Remedy No sound. • A cable is disconnected or the connections are wrong. c Check that the proper connections have been made (see page 9). • The connecting cable used is incorrect. c Use the A/V connecting adaptor (supplied) (see page 9). • The sound is not adjusted properly. c Adjust “Volume” on the Picture menu (see page 21). Remote Commander Symptom Cause and Remedy The Remote Commander does not work. The Remote Commander battery is dead. c Replace it with a new battery (see page 7). Others Symptom Cause and Remedy The control panel keys do not function. The control panel keys are locked. c Unlock the control panel keys (see page 25). Indicators Symptom Cause and Remedy The LAMP/COVER indicator flashes. • The lamp cover or the air filter cover is detached. c Attach the cover securely (see page 32 and 33). • The electrical system may break down. c Consult with qualified Sony personnel. The LAMP/COVER indicator lights up. • The lamp has reached the end of its life. c Replace the lamp (see page 31). • The lamp has reached a high temperature. c Wait for 45 seconds to cool the lamp and then turn on the power again. • If the LAMP/COVER indicator still lights even after you have replaced the lamp, the electrical system may break down. c Consult with qualified Sony personnel. The TEMP/FAN indicator flashes. The fan is broken. c Consult with qualified Sony personnel. The TEMP/FAN indicator lights up. • The internal temperature is unusually high. c Check to see that nothing is blocking the ventilation holes. • The projector is being used at a high altitude. c Ensure that “High Altitude Mode” on the Installation menu is set to “On.” Both the LAMP/COVER and TEMP/FAN indicators light up. The electrical system has broken down. c Consult with qualified Sony personnel. Troubleshooting Messages List Warning Messages Use the list below to check the meaning of the messages displayed on the screen. Message Meaning and Remedy High temp.! Probably use in high altitude. Switch to high altitude mode on? Yes V No v Internal temperature is too high. c When using the projector at an altitude of 1,500 m or higher, set “High Altitude Mode” on the Installation menu to “On” (see page 27). c If this message appears on the screen when using the projector at normal altitudes, check to see if anything is blocking the ventilation holes (exhaust). High temp.! Lamp off in 1 min. The internal temperature is too high. c Turn off the power. c Check to see that nothing is blocking the ventilation holes. Frequency is out of range! • This input signal cannot be projected as the frequency is out of the acceptable range of the projector. c Input a signal that is within the range of the frequency. • The resolution setting of the output signal of the computer is too high. c Set the output setting to XGA (VPL-CX21) and SVGA (VPLCS21) (see page 9). Please check Input-A Signal Sel. You have input an RGB signal from the computer when “Input-A Signal Sel.” on the Setup menu is set to “Component.” c Set “Input-A Signal Sel.” correctly (see page 28). Please replace the Lamp. • It is time to replace the lamp. c Replace the lamp. • When this message appears even after replacing the lamp, the task has not been completed. c Perform the operation of steps 8 and 9 on page 32. Please clean the filter. It is time to clean the filter. c Clean the filter (see page 33). Caution Messages Use the list below to check the meaning of the messages displayed on the screen. Message Meaning and Remedy Not applicable! You have pressed the wrong key. c Press the appropriate key. The panel keys are locked! “Panel Key Lock” on the Function menu is set to “On.” c All the keys on the control panel of the projector are locked. Operate the projector with the keys on the Remote Commander (see page 25). Auto Focus is disabled! Do you wish to enable? Yes V No v “Auto Focus” on the Function menu is set to “Off.” c To enable the Auto Focus function, set it to “On.” Others Troubleshooting Message Meaning and Remedy Lens control is locked! Do you wish to unlock? Yes V No v “Lens Control” on the Installation menu is set to “Off.” c To enable the the LENS (FOCUS, ZOOM) key on the Remote Commander, and the FOCUS and ZOOM keys on the projector, set “Lens Control” to “On.” Troubleshooting Specifications Optical characteristics Projection system 3 LCD panels, 1 lens, projection system LCD panel VPL-CX21: 0.63-inch XGA panel, approximately 2,360,000 pixels (786,432 pixels . 3) VPL-CS21: 0.63-inch SVGA panel, approximately 1,440,000 pixels (480,000 pixels . 3) Lens 1.2 times zoom lens (powered) f 18.8 to 22.6 mm/F1.6 to 1.94 Lamp 165 W Ultra High Pressure lamp Proj...
Otros modelos de este manual:Proyectores - VPL-CX21 (896.15 kb)