Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Horizental Vertical Max Min Offset (M:inch) (X:mm) (Y:mm) (Z:mm) (Z:mm) (Y':mm) Screen size 40 812.8 609.6 1376 1140 102 50 1016.0 762.0 1727 1433 127 60 1219.2 914.4 2078 1726 152 70 1422.4 1066.8 2430 2020 178 80 1625.6 1219.2 2781 2313 203 90 1828.8 1371.6 3133 2606 229 100 2032.0 1524.0 3484 2899 254 110 2235.2 1676.4 3835 3192 279 120 2438.4 1828.8 4187 3485 305 130 2641.6 1981.2 4538 3778 330 140 2844.8 2133.6 4889 4071 356 150 3048.0 2286.0 5241 4364 381 160 3251.2 2438.4 5592 4657 406 170 3454.4 2590.8 5944 4950 432 180 3657.6 2743.2 6295 5243 457 190 3860.8 2895.6 6646 5536 483 200 4064.0 3048.0 6998 5829 508 210 4267.2 3200.4 7349 6122 533 220 4470.4 3352.8 7701 6415 559 230 4673.6 3505.2 8052 6708 584 240 4876.8 3657.6 8403 7001 610 250 5080.0 3810.0 8755 7294 635 260 5283.2 3962.4 9106 7587 660 270 5486.4 4114.8 9457 7880 686 280 5689.6 4267.2 9809 8173 711 290 5892.8 4419.6 10160 8466 737 300 6096.0 4572.0 10512 8759 762 This projector is designed to show images optimally on a 80 ~ 120 inch sized screen. A. Screen Z: Projection distance Y': Distance from Lens Center to Image Bottom Adjusting the H-Keystone 1. Check the projection distance according to the screen size and then install the projector (see the table below). Screen size (m) Diagonal Width 1 0.8 1.3 1 1.5 1.2 1.8 1.4 2 1.6 2.3 1.8 2.5 2 2.8 2.2 3 2.4 3.3 2.6 3.6 2.8 3.8 3 4.1 3.3 4.3 3.5 4.6 3.7 4.8 3.9 5.1 4.1 5.3 4.3 5.6 4.5 5.8 4.7 6.1 4.9 6.4 5.1 Length 0.6 0.8 0.9 1.1 1.2 1.4 1.5 1.7 1.8 2 2.1 2.3 2.4 2.6 2.7 2.9 3 3.2 3.4 3.5 3.7 3.8 Projection distance (m) 1.4 1.7 2.1 2.4 2.8 3.1 3.4 3.8 4.1 4.5 4.8 5.1 5.5 5.8 6.2 6.5 6.8 7.2 7.5 7.9 8.2 8.5 Projection distance (ft) 4.5 5.5 6.8 7.8 9.1 10.1 11.1 12.4 13.4 14.7 15.7 16.7 18.0 19.0 20.3 21.3 22.3 23.6 24.6 25.9 26.9 27.8 A : Projector B : Projection distance C : Screen - Projection distance: Vertical distance from a projected picture 6.6 5.3 4 8.9 29.1 6.9 5.5 4.1 9.2 30.1 7.1 5.7 4.3 9.6 31.4 7.4 5.9 4.4 9.9 32.4 7.6 6.1 4.6 10.2 33.4 2. Select one from Front-Floor, Front-Ceiling, Rear-Floor and Rear-Ceiling according to the location to install the projector. 3. Set the values of the H-Keystone and the V-Keystone to '0' and place the zoom knob right in the middle of its movement range. 4. Press the MENU button to display the Crosshatch screen of the Test Pattern. (Setup > Test Pattern > Crosshatch) 5. Adjust the location of the projector until lines . and . in the picture below become parallel. Screen Crosshatch Test Pattern . A virtual vertical line made on the screen using a piece of thread, etc. . A vertical line in the middle of the Test Pattern 6. Adjust the projector's angle so that a corner of the projected picture (which is nearest to the projector) meets that of the screen. A : Projector B : Screen C : Projected image D : A corner of the picture nearest to the projector > Adjust the projector's angle until the projected image covers the entire screen area (The projected image may not cover the entire screen area depending on the projector's installation height. In this case, adjust the projector's angle so that the entire screen area can be covered.) 7. Press the V.KEY-STONE button on the remote control. The V-Keystone menu will be displayed. Adjust V-Keystone using the + or - button on the remote control. -A : Projector - B : Screen - C : Projected image > Keep adjusting until the vertical line on the Test Pattern becomes parallel with the outer vertical line on the screen. 8. Press the ^ or Ў button to select H-Keystone. Adjust H-Keystone using the + or - button on the remote control. - A : Projector - B : Screen - C : Projected image Keep adjusting until the horizontal line on the Test Pattern becomes parallel with the outer horizontal line on the screen. > 9. Adjust the screen size using the zoom knob. 10. If any part of the projected image is larger than the screen, adjust the size of the projected image using the Custom option in the Size menu. How to adjust: 1. Press the MENU button. 2. Select Picture to move on to the Size menu. 3. Select the Custom option and then select an area to adjust. 4. Adjust the screen size using the ^ or Ў button. -A : Projector - B : Screen - C : Projected image > Keystone, which is a feature to calibrate an image skew, may degrade the brightness and resolution once it is activated. Setting up the PC Environment - Check the following items before connecting your PC to your projector. 1. Click the right mouse button on the Windows desktop and click on [Properties].
Proyectores - SP-L330H (1.33 mb)
Proyectores - SP-L350 (1.33 mb)
Proyectores - SP-L350W (1.33 mb)