Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge. Improper mounting could cause the projector to fall, resulting in an accident. • If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let everyone involved with the use of the projector know that.fact. T urning f Connecting 1 Insert the power AC IN socket of 2 Insert the power cord When the power cord is plugged in, the following three green indicators will come several seconds: ON, TEMP, and LAMP. Next, the ON indicator will change to orange, indicating standby mode. (Do not perform any operations while the 3 green (Supplied) Power cord connector indicators are on.) Removing the lens cover Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat. Turning the power on Remote Control panel Control Press the ON/STANDBY FAN TEMP LAMP ON VOL. + VOL. - ON / STANDBY INPUT MENU AUTO SET KEYSTONE INPUT ON/ STANDBY CALL MUTE RESIZE FREEZE AUTOSET KEYSTONE CANCEL ZOOM+ ZOOM- Start-up screen button. The power turns on, and the following 3 green indicators light: ON, LAMP, and FAN. After a moment, the startup screen appears. Notes • The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to appear via the Display setting menu p.31 . • The first time you use the projector after purchase, after the start-up screen disappears, the Language menu is displayed p.22 . 20 Turning the 1 Press the ON/STANDBY button. A message appears on that you wish to shut off the power. This message will disappear after (This operation is no longer after the message disappears.) 2 Press the ON/STANDBY button again. The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode. When cooling lamp During internal cooling After cooling is completed FAN TEMP LAMP ON FAN TEMP LAMP ON FAN TEMP LAMP ON (Green) (Green) (Orange) (Off) (Off) (Orange) Flashing (Green) (Off) (Orange) A B C A B C During cooling, the LAMP indicator flashes. In this state, the power cannot be turned back on. In addition, unplugging the power cord in this state will shorten the life of the lamp. After the LAMP indicator goes off, the cooling fan continues to operate for a short while in order to expel excess internal heat. If you are in a hurry, there is no problem with unplugging the power cord in this state. In standby mode. Note • The projector consumes about 6W of power in standby. We recommend you to unplug the power cord if you will not use the projector for an extended period. PRECAUTIONS • Before unplugging the power cord, make sure that the LAMP indicator is off. Unplugging the power cord and cutting off the power while the projector is running or being cooled will shorten the life of the lamp. However, please unplug the power cord if the projector locks up or acts abnormally. • If the power cord was unplugged before cooling was complete, give the lamp sufficient time to cool before plugging it back in. If the lamp overheats, it may fail to light, and its lifetime will be shortened. LCD Panels LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the following precautions. • In order to extend the lifetime of the LCD panel, always turn off the power when not in use, and make sure that the lamp is off. Keeping the lamp off is also very effective at saving electricity. • If the air filter becomes dirty and clogged, the projector’s internal temperature will rise, shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter from time to time p.32 , and replace it periodically. Contact the store where you purchased your projector, or your local Service Station for replacement air filters. 21 Operations WARNING • Do not look into the lens during operation. Doing so could damage your vision. CAUTION • Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating. • Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object. Basic 1 Turn on the Turn on the power by following the instructions in “ Turning on the power” p.20 . 2 Select the language first time). When the projector is used for the first time after purchase, menu for language and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6.) q Use the or buttons to select the ............... . English English .............. desired language and press the button. Francais French Deutsch German ............. . Message for setup confirmation is displayed in a ............... . selected language. .............
Otros modelos de este manual:Proyectores - TLP-S10U (3.28 mb)