Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge. Improper mounting could cause the projector to fall, resulting in an accident. a is the distance (m) between the lens and the screen, and corresponds to a range of 1.41 m to 11.45 m. Screen As seen from above Lens center As seen from the side screen projection distance a(m) size (cm) min length max length (zooming max) (zooming min) 32 (81) — 1.41 40 (102) 1.49 1.79 60 (152) 2.26 2.70 80 (203) 3.02 3.62 100 (254) 3.79 4.53 150 (381) 5.70 6.82 200 (508) 7.62 9.11 250 (635) 9.53 11.40 300 (762) 11.45 — AC IN AC IN a (min length) = projection size (inches) – 1.082 26.107 a (max length) = projection size (inches) – 0.906 21.854 Operating the remote control Point the remote control toward the projector’s infrared remote sensor, and press a button on the remote control. • Operating the projector from the front Approx. 15.. Approx. 5m • Operating the projector from the rear Approx. 15.. Approx. 5m Loading dry-cell batteries into the remote control q Remove the battery cover. w Insert the dry-cell batteries. Be sure to align the plus and minus ends of the batteries properly. Two batteries (LR03 or R03, SIZE AAA) are used. e Replace the battery cover. Dry-cell batteries • Remove batteries from remote control when not using for extended periods. • If the remote control stops working, or if its range decreases, replace all the batteries with new ones. The remote control • The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting. • Do not drop or bang. • Do not leave in hot or humid locations. • Do not get wet or place on top of wet objects. • Do not take apart. • In rare cases, ambient conditions could impede the operation of the remote control. If this happens, point the remote control at the main unit again, and repeat the operation. Preparing and using the remote control 19 Operations 18 Connecting the power cord 1 Insert the power cord connector into the AC IN socket of the projector. 2 Insert the power cord plug into a wall or other power outlet. Removing the lens cover Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat. Turning the power on Press the ON/STANDBY button. The power turns on, and the following 3 green indicators light: ON, LAMP, and FAN. After a moment, the start-up screen appears. CAUTION • Do not look into the lens during operation. Doing so could damage your vision. • Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating. • Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object. Notes • The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to appear via the Display setting menu p.29 . • The first time you use the projector after purchase, after the start-up screen disappears, the Language menu is displayed p.21 . Turning the power on and off When the power cord is plugged in, the following three green indicators will come on for several seconds: ON, TEMP, and LAMP. Next, the ON indicator will change to orange, indicating standby mode. (Do not perform any operations while the 3 green (Supplied) Power cord connector indicators are lit.) Start-up screen FAN TEMP LAMP ON VOL.- VOL.+ INPUT ON / STANDBY MENU AUTO SET AUTO KEYSTONE INPUT ON/ STANDBY RESIZE OFF CALL AUTO MUTE RESIZE FREEZE KEYSTONE SET Control panel Remote Control COMPUTER VIDEO S-VIDEO ( Y/PB/PR ) CONTROL AUDIO VIDEO MONITOR Before connection • Read the owner’s manual of the device to be connected to the projector. • Some types of computer cannot be used connected to this projector. Check for an RGB output terminal, supported signal p.36 , etc. • Turn off the power of both devices before connection. • The figure below is a sample connection. This does not mean that all of these devices can or must be connected simultaneously. (Dotted lines mean items can be exchanged.) Note • The AUDIO terminal is common among all the devices for input terminal. Connection Computer CRT monitor, etc. To audio output Audio cable (for computer) (supplied) To RGB output Control cable To RS-232C terminal Computer (for control) RGB cable (supplied) To Y/CB/CR output Green (Y) Blue (CB), Red (CR) Yellow (to video output) To audio output White (L) Red (R) VCR S-Video cable (not supplied) Video cable (supplied) To S-Video output To audio output White (L) Red (R) Monitor cable Mini D-sub 15P-BNC (not supplied) Audio cable (supplied) DVD player Conversion adapter BNC-pin (not supplied) p.38 T urning ) Turning the 1 Press the ON/STANDBY button. A message appears on that you wish to shut off the power. This...
Otros modelos de este manual:Proyectores - Mobile Projectors TLP-T50MU (1.86 mb)
Proyectores - TLP-S30U (1.86 mb)
Proyectores - TLP-T50MU (1.86 mb)