Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
If there are parts missing and/or damaged, please stop the installation and contact Sony Electronics (800) 222-7669. NOTE: Please review all WARNING and CAUTION statements (see Page 8) before beginning the installation of the PAM-200. PAM-200 (Qty 1) M4 x 10mm Security Screw (Qty 3) M4 x 16mm Security Screw (Qty 3) #14 X 2” Wood Screw (Qty 3) Nylon Spacers (Qty 3) M4 x 12mm Security Screw (Qty 2) M4 External Washer (Qty 2) Installation Tools Phillips Head Screw Driver Portable Drill Soft Material/ Blanket Pencil Tape Measure Stud Finder (Commercially Available) Ladder M5 Security Allen Wrench (Supplied) M3 Security Allen Wrench (Supplied) Masonry Bit (Commercially Available) .” Wood Drill Bit – Ceiling Installation 5/16” Masonry Drill Bit – Concrete Installation (Commercially Available) (Commercially Available) Installation Manual Page - 3 - PAM-200 Features Congratulations on the purchase of your new Sony Electronics PAM-200 Projector Mount. The projector mount can be configured for ceiling installations. The PAM-200 features MagnaGuide™ Technology which assists the installer for quicker installation times and peace of mind. The PAM-200 Projector Mount is height adjustable from 9” to 12” to help achieve the perfect viewing height. A Solid Structure Mounting Points B Single Wooden Stud Mounting Points C Ceiling Plate D M6 x 20mm Security Screw E Adjustable Suspension Neck F MagnaGuide™ - Upper Assembly G M4 x 12mm Security Screw and Star Washer H Locking Tab I Mounting Hardware J Magnets K MagnaGuide™-Lower Assembly L Radial Glide™ Set Screw M Projector Plate Optional Mounting Hardware N M4 x 12mm Security Head Screw O Nylon Spacer Selecting the Proper Mounting Hardware 1. Invert the projector and locate the mounting points. 2. Test each size of the screws provided. 3. The correct screws should thread easily into the mounting point and not pull out when pressure is applied. WARNING: DO NOT OVERTIGHTEN YOUR MOUNTING SCREWS TO THE PROJECTOR CHASIS. USING THE INCORRECT SCREW DEPTH MAY CAUSE DAMAGE TO YOUR PROJECTOR. Page - 4 - Installation Manual PAM-200 Attaching the Mount Unpack the PAM-200 and review any WARNING statements that apply to the installation. Select the desired location for the PAM-200. M4 x 10mm Security Head Screw M5 Allen Wrench 2. Line up the mounting holes on the PAM-200 with the mounting points of the projector. 3. Use three (3) M4 x 10mm security head screws to attach the PAM-200 to the projector. 4. Tighten the security head screws down with a M5 Security Allen wrench (supplied). 5. Do not overtighten these screws, as the threaded inserts can be damaged. Optional Hardware When mounting the PAM-200 to a Sony projector, it is imperative that the projector plate not cover any access plates that allow the user to access the interior of the projector. The following steps will allow the user to mount the PAM-200 projector bracket to the Sony projector without fear of blocking any ventilation access plates. 1. Locate the mounting points on the bottom of the projector (see arrows above for mounting point recognition). Nylon Spacer M4 x 16mm Security Head Screw Nylon Spacer M5 Allen Wrench 1. Locate the mounting points on the bottom of the projector 3. Line up the mounting holes of the PAM-200 with the (see arrows above for mounting point recognition). nylon spacer mounting holes. 2. Place the nylon spacers over the mounting points. 4. Use three (3) M4 x 16mm security head screws to attach the PAM-200 to the projector. 5. Tighten the security head screws down with a M5 Security Allen wrench (supplied). 6. Do not overtighten these screws, as the threaded inserts can be damaged. Installation Manual Page - 5 - PAM-200 Ceiling Installation 1. Mounting Surfaces NOTE: Use a 1/4” drill bit to pre-drill the mounting holes before securing the wood screws (supplied). Wood studs: Where denoted with the letter ‘A’, mark these locations for wood stud installation. NOTE: Use a masonry bit to pre-drill the mounting holes in the concrete surface. Concrete surface: Where denoted with the letter ‘B’, mark these locations for concrete installation. 2. Use two (2) #14 x 2” wood screws (supplied) to attach the ceiling plate to the wooden ceiling stud. NOTE: For extra security, attach a third wood screw to the middle mounting point (A). 3. Slowly raise the projector toward the upper assembly. Once the projector is close to the upper assembly, MagnaGuide Technology will pull the lower assembly into the upper assembly and the locking tab will engage. WARNING: THE MAGNETS ARE USED FOR GUIDING THE UNIT ONLY! PLEASE MAKE SURE THE TWO (2) M4 X 12MM SCREWS ARE USED TO SECURE THE PROJECTOR. 4. Attach the two (2) M4 x 12mm security screws and washers that are located on each side of the locking tab. NOTE: Do not release your hold on the projector until the upper and lower assemblies are engaged and the locking tab is in place. NOTE: If you choose to use the center mounting point for added security, detach the adjustable suspen...