Votos - 2, Puntuación media: 4
(
)
)
|
Fotos y especificaciones Acer H5360 |
Resumen del manual
• If you select "Always request password while projector turns on", the user has to enter the password every time when the projector is turned on. Administrator Password The "Administrator Password" can be used in both the "Enter Administrator Password" and "Enter Password" dialog boxes. • Press to change the "Administrator Password". • The factory default of "Administrator Password" is "1234". If you forgot your administrator password, do the following to retrieve the administrator password: • An unique 6-digit "Universal Password" which is printed on the Security Card (please check accessory in the box). This unique password is the number which will be accepted by projector anytime no matter what the Administrator Password is. • If losing this security card and number, please contact with an Acer service center. Reset • Press the button and choose "Yes" to return the parameters on all menus to the factory default settings. 23 Management ECO Mode Choose "On" to dim the projector lamp which will lower power consumption, extend the lamp life and reduce noise. Choose "Off" to return normal mode. High Altitutde Choose "On" to turn on High Altitude mode. Operate the fans at full speed continuously to allow for proper high altitude cooling of the projector. Auto Shutdown The projector will automatically shutdown when there is no signal input after the allocated time. (in minutes) Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours). Lamp Reminding Activate this function to display a reminder to change the lamp 30 hours before its expected end-of-life. Lamp Hour Reset Press the button and choose "Yes" to turn the lamp hour counter to 0 hours. Audio Volume • • Press to decrease the volume. Press to increase the volume. Mute • • Choose "On" to mute the volume. Choose "Off" to restore the volume. Power On/Off Volume • Select this function to adjust the notification volume when turning the projector on/off. Alarm Volume • Select this function to adjust the volume of any warning votifications. English EnglishEnglish 24 Timer Timer Location • Choose the location of the timer on the screen. Timer Start • Press to start or stop the timer. Timer Period • Press or to adjust the timer period. Timer Volume • Select this function to adjust the nitification volume when the timer function is enabled and time is up. Timer Display • Press or to which timer mode to display on the screen. Language Language Choose the multilingual OSD menu. Use the to select your preferred menu language. • Press to confirm the selection. or key 25 Appendices Troubleshooting If you experience a problem with your Acer projector, refer to the following troubleshooting guide. If the problem persists, please contact your local reseller or service center. Image Problems and Solutions # Problem Solution 1 No image appears onscreen • Connected as described in the "Getting Started" section. • Ensure none of the connector pins are bent or broken. • Check if the projector lamp has been securely installed. Please refer to the "Replacing the Lamp" section. • Make sure you have removed the lens cap and the projector is switched on. 2 Partial, scrolling or incorrectly displayed image(For PC (Windows 95/98/ 2000/XP)) • Press "RESYNC" on the remote control. • For an incorrectly displayed image: • Open "My Computer," open the "Control Panel," and then double-click the "Display" icon. • Select the "Settings" tab. • Verify that your display resolution setting is lower than or equal to UXGA (1600 x 1200). • Click the "Advanced Properties" button. If the problem still appears, change the monitor display you are using and follow the steps below: • Verify that the resolution setting is lower than or equal to UXGA (1600 x 1200). • Click the "Change" button under the "Monitor" tab. • Click "Show all devices". Next, select "Standard monitor types" under the SP box, and choose the resolution mode you need under the "Models" box. • Verify that the resolution setting of the monitor display is lower than or equal to UXGA (1600 x 1200). English 26 English 3 Partial, scrolling or incorrectly displayed image (For notebooks) • Press "RESYNC" on the remote control. • For an incorrectly displayed image: • Follow the steps for item 2 (above) to adjust the resolution of your computer. • Press the toggle output settings. Example: [Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8], Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5 ] • If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the projector. 4 The screen of the notebook computer is not displaying your presentation • If you are using a Microsoft® Windows® based notebook: Some notebook PCs may deactivate their own screens when a second display device is in use. Each has a different way to be reactivated. Refer to your computer's manual for detailed information. • If you are using an Apple® Mac® OS based notebook: In System Preferences, op...