This will help to insure proper cutting and a good fit. Now, mark the locations for the speakers mounting screws, remove the panel and drill the screw holes. When finished you may replace the panel. . After cutting and drilling all holes, inspect the mounting areas for any metal burrs or rough edges. File any area that may interfere with the mounting of the speaker. . Clean any metal shavings from the mounting area and check for areas in which water may enter the speaker cavity. Treat the area

Turn on the various components and slowly advance the volume. Remember to check and re-check all connections to insure proper installation and use. • Do not continuously use the speaker system beyond the nominal power handling capacity. • Keep recorded tapes, watches, and personal credit cards using magnetic coding away from the speaker system to protect them from damage caused by the magnets in the speakers. • If you cannot find the appropriate mounting location, consult your car dealer or y

В противном случае наблюдается искажение цветов изображения, негативно отражающееся на впечатлениях от просмотра. Закройте гардины или уменьшите интенсивность источника освещения, если экран необходимо установить в светлом помещении. Не подвергайте проектор ударным нагрузкам и вибрации ■ Не допускайте воздействия внешних нагрузок на объектив с тем, чтобы не повредить поверхность его линз. Обеспечьте возможность периодического отдыха для глаз ■ Длительный просмотр изображения на экране приво

При эксплуатации в домашних условиях он может оказаться источником радиопомех. В этом случае Вам необходимо будет прибегнуть к соответствующим мерам. 1 Введение УТИЛИЗАЦИЯ ИЗДЕЛИЯ В конструкции проектора использован свинцово-оловянный припой, а в составе заполнения лампы содержится небольшое количество ртути. Утилизация данных материалов может регулироваться требованиями законодательства об охране окружающей среды. По вопросу об утилизации заменяемых узлов обратитесь в местные органы управле

It is necessary to refer the manual. • Do not install the speakers where they may be subjected to excessive heat moisture, dust or where they will be kicked repeatedly, brushed or bumped. • Before mounting and connecting the wires be sure that wire of the negative pole terminal is disconnected from accumulator. Nonobservance of this demand may cause the short circuit or fire. • To prevent short circuit never put or leave any metal objects (e.g. coins or metal tools) inside the acoustic system

It is necessary to refer the manual. • Do not install the speakers where they may be subjected to excessive heat moisture, dust or where they will be kicked repeatedly, brushed or bumped. • Before mounting and connecting the wires be sure that wire of the negative pole terminal is disconnected from accumulator. Nonobservance of this demand may cause the short circuit or fire. • To prevent short circuit never put or leave any metal objects (e.g. coins or metal tools) inside the acoustic system

This will help to insure proper cutting and a good fit. Now, mark the locations for the speakers mounting screws, remove the panel and drill the screw holes. When finished you may replace the panel. • After cutting and drilling all holes, inspect the mounting areas for any metal burrs or rough edges. File any area that may interfere with the mounting of the speaker. • Clean any metal shavings from the mounting area and check for areas in which water may enter the speaker cavity. Treat the area

Обратитесь к ближайшему дилеру, имеющему полномочия от фирмы Sharp или в сервисный центр. 10 Наименования узлов и органов управления Числа внутри таблички указывают номера страниц руководства, на которых приводится описание данного органа управления или данной функции. Проектор Вид сверху Индикат°рР““^ питания Кнопка STANDBY/ON Для включения питания и переключения проектора в режим ожидания. Кнопка ENTErB^^ Для ввода выбранных или отрегулированных позиций меню. Кнопка keystone Для

It is necessary to refer the manual. • Do not install the speakers where they may be subjected to excessive heat moisture, dust or where they will be kicked repeatedly, brushed or bumped. • Before mounting and connecting the wires be sure that wire of the negative pole terminal is disconnected from accumulator. Nonobservance of this demand may cause the short circuit or fire. • To prevent short circuit never put or leave any metal objects (e.g. coins or metal tools) inside the acoustic system

It is necessary to refer the manual. Do not install the speakers where they may be subjected to excessive heat moisture, dust or where they will be kicked repeatedly, brushed or bumped. Before mounting and connecting the wires be sure that wire of the negative pole terminal is disconnected from accumulator. Nonobservance of this demand may cause the short circuit or fire. To prevent short circuit never put or leave any metal objects (e.g. coins or metal tools) inside the acoustic system. Make