Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Your Indoor/Outdoor Modular Intercom System operates as a two-tone doorbell intercom and an indoor intercom. The doorbell is simple to install without wiring and you can add additional stations. PREPARATION Installing the Doorbell’s Batteries Your doorbell intercom uses four AA batteries (not supplied) for power. For the best performance and longest life, we recommend RadioShack alkaline batteries. Caution: Use only fresh batteries of the required size and recommended type. Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities. 1. Use a Phillips screwdriver to loosen the screws in the doorbell intercom’s battery compartment cover, then lift the cover off. 2. Insert four AA batteries into the compartment as indicated by the polarity symbols (+ and –) marked inside. 3. Replace the cover and tighten the screws. Hint: For convenience, set the channel (see “Setting the Channel”) while you have the battery cover removed. Replace the batteries when the battery level is low and the doorbell sends an alert tone to the indoor intercom. The POWER indicator on the indoor intercom flashes until you replace the batteries. Warning: Dispose of old batteries promptly and properly. Do not burn or bury them. Caution: If you do not plan to use the doorbell for two weeks or longer, remove the batteries. Batteries can leak chemicals that can destroy electronic parts. If the doorbell unit operates under severe cold weather, use a lithuim type AA battery. Setting the Channel The doorbell and indoor intercoms have three selectable operation channels to prevent interference from similar products nearby. Select the same channel for both the doorbell intercom and the indoor intercom. On the doorbell intercom, slide CH inside the battery compartment to 1 (49.835MHz), 2 (49.860MHz), or 3 (49.885MHz). On the back of the indoor intercom, set OUTDOOR CHANNEL to the same channel number (1, 2 or 3) you chose for the doorbell intercom. Note: If the doorbell occasionally sounds without anyone pressing BELL on the doorbell, change the channel settings. Changing the Doorbell’s Tone Use a small flat-blade screwdriver to carefully pull out the jumper TONE switch located in the battery compartment, then insert the jumper TONE switch into the other two pins. © 2001 RadioShack Corporation. All Rights Reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation. Setting the Doorbell’s Volume Slide VOL located inside the battery compartment to level 1, 2 or 3. Testing the Doorbell Test the doorbell before permanently mounting it. With the indoor intercom plugged into a standard AC outlet, adjust VOLUME on the indoor intercom to its middle position. Press BELL on the doorbell intercom. The doorbell should sound. Mounting the Doorbell 1. Drill four 3/16 inch diameter holes into the mounting surface. Insert an anchor into each hole. 2. Align the supplied metal mounting bracket with the drilled holes and drive a screw (not supplied) through the bracket into each hole. Do not overtighten the screws. 3. Align the slot on the back of the doorbell with the hook on the mounting bracket. Carefully push the doorbell onto the hook and slide it down to secure it. 4. Once the doorbell is securely on the bracket, insert the pan-head machine screw (supplied) through the hole on the lower edge of the doorbell into the threaded holes in the bracket. Mounting the Indoor Intercom Follow these steps to mount the indoor intercom on a wall. Note: You need two screws (not supplied) with heads that fit into the keyhole slots on the bottom of the intercom. 1. Mark the mounting screw locations 21/2 inches (64 mm) apart, one above the other. 2. Drill a starter hole at each mark. 3. Thread a screw into each hole until the screw’s head extends about 1/8 inch (3.5mm) from the wall. 4. Align the keyhole slots on the bottom of the intercom with the screw heads in the wall, then slide the intercom down to secure it and lift and extend the antenna. Connecting the Indoor Intercom to AC Power Locate a standard AC outlet in the area where you want to hear the chime and use the intercom. Plug the indoor intercom’s power cord into the outlet. Caution: This product is equipped with a three-wire grounding-type plug ( a plug having a third grounding pin). This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into your AC outlet, contact your electrician to replace your outlet. Do not defeat the safety purpose of the grounding- type plug. Important: Be sure you install the stations at least 10 feet away from each other. Placing the stations too close together produces feedback (a squeal or howl from the speakers). The stations can transmit up to 300 feet, including between buildings, as long as they are connected to the same power line transformer. OPERATION Turning the Indoor Intercom On and Off and Adjust...