Votos - 1, Puntuación media: 5
(
)
)
|
Resumen del manual
Caution: The battery compartment cover is attached to the module. Do not try to remove it completely. 4. Place the batteries in the compartment, as indicated by the polarity symbols (+ and –) marked inside. 5. Close the cover and secure it with the screw. If you are replacing the batteries, reconnect the phone line, AC adapter, and the phone. When BATT (battery) appears or the display dims, replace the batteries. Warning: Dispose of old batteries promptly and properly. Do not burn or bury them. Preparation 9 43-947.fm Page 10 Thursday, May 25, 2000 11:36 AM Caution: If you do not plan to use the module for a month or more, remove the batteries. Batteries can leak chemicals that can destroy electronic parts. CONNECTING THE AC ADAPTER The module uses the supplied 9V, 200-mA AC adapter for power. Cautions: ! You must use a Class 2 power source that supplies 9V DC and delivers at least 200 mA. Its plug must fit the module's 9V DC 200mA jack. The supplied adapter meets these specifications. Using an adapter that does not meet these specifications could damage the module or the adapter. • Always connect the AC adapter to the module before you connect it to AC power. When you finish, disconnect the adapter from AC power before you disconnect it from the module. • The supplied adapter was designed specifically for your module. Use only the supplied adapter. To power the module, plug the adapter’s barrel plug into 9V DC 200mA on the back of the module. Then connect the other end of the adapter to a standard AC outlet. 10 Preparation 43-947.fm Page 11 Thursday, May 25, 2000 11:36 AM CONNECTING THE MODULE Your module connects to any modular phone jack and your phone. You can also connect it to an answering machine. Note: The module might not work with older phones, such as Western Electric phones. Connecting to a Single-Line Phone 1. Disconnect the telephone line cord from the phone and plug it into the module’s TO LINE jack. 9V DC 200mA TO LINE TO PHONE 2. Plug one end of the supplied line cord into the module’s TO PHONE jack. 3. Plug the other end of the cord into the phone’s jack. Connecting to a Two-Line Phone To record information about calls received on a two-line phone, you can connect two CID-947 modules using a triplex adapter. Each module only records information about calls received on the line to which it is connected. Preparation 11 Follow these steps to connect two CID-947 modules to a two- line phone. 1. Disconnect the telephone line cord from the modular phone jack (on the wall) and plug it into L1+L2 on the triplex adapter. Triplex Adapter L1 L2 L1+L2 43-947.fm Page 12 Thursday, May 25, 2000 11:36 AM Triplex Adapter L1 L2 L1+L2 43-947.fm Page 12 Thursday, May 25, 2000 11:36 AM 2. Plug the triplex adapter into the modular phone jack. 3. Plug one end of the supplied line cord into the TO LINE jack on one of the modules. 4. Plug the other end of the cord into either L1 or L2 on the triplex adapter. 5. Repeat Steps 3 and 4 to connect another module to the remaining open jack (L1 or L2) on the triplex adapter. 12 Preparation Connecting to an Answering Machine To Phone TO LINE TO PHONE 43-947.fm Page 13 Thursday, May 25, 2000 11:36 AM To Phone TO LINE TO PHONE 43-947.fm Page 13 Thursday, May 25, 2000 11:36 AM 1. Disconnect the phone line cord that connects your answering machine to the phone line from the answering machine’s jack. Then plug it into the module’s TO LINE jack. 2. Plug one end of the supplied line cord into the module’s TO PHONE jack. 3. Plug the cord’s other end into the answering machine’s jack. 4. Set your answering machine to answer after two or more rings. This gives the module time to record the call information that the phone company sends between the first and second rings. MOUNTING THE MODULE You can place the module directly on a desk, shelf, or table by itself or using the stand on the supplied mounting bracket. Or, you can use the bracket to mount the module on a wall. Preparation 13 43-947.fm Page 14 Thursday, May 25, 2000 11:36 AM Attaching the Mounting Bracket 1. Align the slots on the bottom of the module with the hooks on the mounting bracket. 2. Gently push the module down on the bracket to secure it. If you are placing the module on a desk, shelf, or table, pull out the stand on the back of the bracket until it clicks. To remove the module from the bracket, press up from the bottom of the module until it snaps off the bracket. Mounting on a Wall To mount the module on the wall, you need two screws (not supplied) with heads larger than the keyhole slots on the back of the mounting bracket. 1. Using the keyhole slots in the supplied mounting bracket as a template, mark the mounting screw locations on the wall. 2. Drill a hole in the wall at each marked location. 3. Thread a screw through each hole, letting the head extend 1/8-inch (3.5-mm) from the wall. 14 Preparation 43-947.fm Page 15 Thursday, May 25, 2000 11:36 AM 4. Attach the mounting bracket to the module (see “Attachin...