Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
In the box you will find: • Base Unit • Handset • Coiled Handset cord • Telephone line cord for Base unit • User manual Keep the packing materials in a safe place in case you later need to transport Keep your sales (till) receipt, which is your guarantee. the unit 1. LCD Screen 3. M1,M2,M3 Memory buttons 4. Scroll Up & Down buttons 5. Delete button 6. Set/Store button 7. Memory button 8. LNR(Last Number Redial) button 9. Speakerphone button 10. Mute button 11.R(Recall) button 12.Pause button 2. Ringer light indication 1 2 34 5 6 7 8 9 10 11 12 2. Installation 1. Locating the Base unit The Base unit should be placed on a level surface, in a position where: .. the telephone line cable will reach your telephone line socket or extension socket. .. it is not close to a sink, bath or shower, or anywhere else where it might get wet. .. it is not close to other electrical equipment - fridges, washing machines, 2. Plug the coiled handset cord into the Handset. Plug the other end into the jack on the left side of the Base unit. 3. Place the Handset in the Base unit. Make sure the plugs click into place. 4. Plug the telephone line cord free end into a modular wall jack. Press the cable into the groove so 5. Lift the Handset and check for Dial tone in the earpiece. Always use the telephone line cord supplied with your Spirit 410 phone. Other telephone line cords may to Modular not work. Wall jack microwave ovens, TVs, fluorescent lights, etc. that the Base unit stands level. .. Installing (or Replacing) the Battery IMPORTANT - Before removing the battery compartment cover,always make sure the base unit is disconnected from the telephone line. Install 2 pcs of Alkaline AAA batteries into the battery compartment and place back the cover before use. Note: 1) Please do NOT use Rechargeable batteries in this phone. 2 ) $! #( $#"$ $ ' $! # )% will show up of the SIZE AAA SIZE AAA SIZE AAA SIZE AAA #% & ' $ !# 3. Desk/Wall mount installation To place the Spirit 410 on a desk, connect the bottom of the phone in the slots near the rear of the base as shown below. Desk Mount Insert the rigid clips of the stand into the slots the phone (near the rear of the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, ( the stand, and then (3) slide up and forward (3) as shown below. To place the Spirit 410 on a wall, connect bottom of the phone in the cover as shown Wall Mount below. the stand to on the bottom of the base). Press down firmly until 2) pull back the stand to the slots near the front of the base and 0 inatone .com/ 08453459677 0818762092 3 online Desk/Wall mounting continue... Insert the rigid clips of the stand into the slots on the bottom of near the front of the flexible clips clicks into place. To remove the stand, (1) pinch the flexible the stand, and then (3) slide up and forward as shown below. Mark two points on the wall that are 92mm apart to lay the fixing centers as shown below. the phone ( the base). Press down firmly until clips, (2) pull back BE CAREFUL to check that there are no in the wall. Fix two screws (supplied with the unit) at the approximately 7mm Hang the cradle unit on the screws using the wall mount slots. You may need to remove the tighten the does not wobble cradle with the parking hook on the cradle arranged to fit in the parking recess under the earpiece on the Handset. 9 electrical wires hidden marked locations, between the wall and the the screw head. telephone from the wall and that the cradle is securely fixed and leaving screws so . Place the Handset on the Set Time/Date 1 In standby mode, press SET/STO button. .. The display shows ' SET 1 DATE '. 2 Press SET/STO button to confirm. .. The 'year' icon will be blinking. 3 Press UP or DOWN button to set the year. 4. Setting up your phone Press the SET/STO button to enter the menu UP DOWN .. SET 1 DATE .. SET 2 LCD .. SET 3 FLASH Note: The system will time out if you leave You will need to set the correct time and date displayed correctly on the display. If you subscribe to a Caller Display service, the will be set automatically on 4 Press SET/STO button to confirm. .. The 'month' icon will be blinking. 5 Press UP or DOWN button to set the month. 6 Press SET/STO button to confirm. .. The 'date' icon will be blinking. 7 Press UP or DOWN button to set the date. 8 Press SET/STO button to confirm. .. The 'hour' icon will be blinking. and then use or buttons to cycle through the following options: more than 8 seconds between key presses. receipt of your first incoming call. 9 Press UP or DOWN button to set the hour. so they can be time and date 10 Press SET/STO button to confirm. .. The 'minute' icon will be blinking. Press SET/STO button to confirm the setting. .. The display shows ' SET 2 LCD ' , you can 11 12 or press DELETE button to return to standby mode. Press UP or DOWN button to set the minute. Setting up continue... continue with programming, Set LCD 1 In standby mode, press SET/STO...