Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Installation 1. Locating the Base unit The Base unit should be placed on a level surface, in a position where: • the telephone line cable will reach your telephone line socket or extension socket. • it is not close to a sink, bath or shower, or anywhere else where it might get wet. • it is not close to other electrical equipment - fridges, washing machines, microwave ovens, TVs, fluorescent lights, etc. 2. Plug the coiled handset cord into the Handset. Plug the other end into the jack on the left side of the Base unit. Installing Backup batteries 3. Place the Handset in the Base unit. 4. Plug the telephone line cord into the PHONE LINE jack at the back of the Base unit. Plug the other end into a modular wall jack. 5. Lift the Handset and check for Dial tone in the earpiece. Always use the telephone line cord supplied with your SpeakEasy 5. Other telephone line cords may not work. 1. Remove the Battery cover and insert 3 X 1.5V AA size alkaline batteries (not included) into the battery compartment paying attention to the polarity marking as shown inside the compartment. 2. Replace the battery cover until it clicks into place. Warning: Disconnect the telephone from the telephone line before changing the batteries. Note: The Caller display will not work without batteries installed. 4 3. Desk/Wall mount installation 3. Desk/Wall mount installation To place the SpeakEasy 5 on a desk, connect the stand to the bottom of the phone in the slots near the ringer cover as shown below. Desk Mount Insert the rigid clips of the stand into the slots on the bottom of the phone (near the ringer cover). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward (3) as shown below. To place the SpeakEasy 5 on a wall, connect the stand to the bottom of the phone in the slots near the battery cover as shown below. Wall Mount Binatone Help Line - 0845 345 9677 Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677Binatone Help Line - 0845 345 9677 Calls are charged at Local Call rate. 5 Desk/Wall mount continue... Insert the rigid clips of the stand into the slots on the bottom of the phone (near the battery cover). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward as shown below. Mark two points on the wall that are 137mm apart to lay the fixing centers as shown below. BE CAREFUL to check that there are no electrical wires hidden in the wall. Fix two screws (supplied with the unit) at the marked locations, leaving approximately 7mm between the wall and the the screw head. Hang the cradle unit on the screws using the wall mount slots. You may need to remove the telephone from the wall and tighten the screws so that the cradle is securely fixed and does not wobble. Place the Handset on the cradle with the parking hook on the cradle arranged to fit in the parking recess under the earpiece on the Handset. 6 4. Setting up your phone 4. Setting up your phone The following section details how to set up your telephone. Press the MENU button to enter the Options menu and then use the UP or DOWN buttons to cycle through the following options: • SET LANGUAGE • SET TIME/DATE • LCD CONTRAST • SET FLASH TIME • EXIT OPTION Note: The system will time out if you leave!more than 15 seconds between key presses. SET With the phone in standby mode: LANGUAGE 1 Press MENU button. • The display shows OPTIONS MENU OPTIONS MENUOPTIONS MENUOPTIONS MENUOPTIONS MENUOPTIONS MENU . 2 Press UP button to go to the language setting. • The display will show SET LANGUAGE SET LANGUAGESET LANGUAGESET LANGUAGESET LANGUAGESET LANGUAGE. 3 Press MENU button to confirm. 4 Press UP or DOWN button to select one of the 11 languages: ENGLISH, FRENCH, SPANISH, GERMAN, ITALY, PORTUGUESE, TURKISH, DANISH, POLISH, SWEDISH, and DUTCH. 5 Press MENU button to confirm. 6 Continue with programming, or press RECALL button to return to standby mode. The date and time on your phone can be SET TIME/ synchronized with the local date and time if you have subscribed to the Caller Display service from your telephone company. (This feature is only available for an analogue PSTN (not ISDN) line). DATE However, you can set the date and time manually: 1 Press MENU button. • The display shows OPTIONS MENU OPTIONS MENUOPTIONS MENUOPTIONS MENUOPTIONS MENUOPTIONS MENU . 7 Setting up continue... 2 Press UP or DOWN button until the display shows SET TIME/DATE SET TIME/DATESET TIME/DATESET TIME/DATESET TIME/DATESET TIME/DATE. 3 Press MENU button to confirm. • The ‘year’ icon will be blinking. 4 Press UP or DOWN button to set the year. 5 Press MENU button to confirm. • The ‘month’ icon will be blinking. 6 Press UP or DOWN button to set the month. 7 Press MENU button to confirm. • The ‘date’ i...