Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Please also read Part 1 – Important Product Information. AT&T and the globe symbol are registered trademarks of AT&T Corp. licensed to Advanced American Telephones. © 2001 Advanced American Telephones. All rights reserved. Printed in China. Issue 1AT&T 05/01 INSTALLATION Before You Install Batteries Choose a location for the answering system near a modular telephone jack and a standard electrical outlet not controlled by a wall switch. Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111. Input: 120 V, 60 Hz. Output: 6V AC, 350 mA. Standard Electrical Outlet Strain-relief tab 5 Connect the line cord to a modular wall jack. 4 Connect the long line cord to telephone. 6 Connect the handset to the telephone. Plug one end of the coiled cord into the handset jack on the side of the phone. Plug the other end of the coiled cord into the handset, then hang up. 7 Connect the power cord. Table/Desk Installation 1 Remove the base. Slide the base sideways as indicated by the REMOVE arrow (see illustration on page 2). 2 Install batteries as shown. 3 Reinstall the base. Turn the base so the larger end is toward the top of the telephone. Insert the base tabs into the slots, then slide sideways in the direction of the INSTALL arrow to lock the base into the phone. Turn the telephone right side up; it should sit flat on your table during use. • You should install four fresh AA alkaline batteries in order to use this system in case of a power failure. The batteries are not necessary for operation other than during a power failure. • When battery power is low, the LOW BATT light goes on. Replace the batteries promptly, to be able to make and answer calls, and receive and access messages in a power failure. Battery Installation (optional) Modular Telephone Jack The MessageWindow flashes CL to indicate that you need to set the clock (see “Setting the Clock” in the ANSWERING SYSTEM OPERATION section of this manual). 8 Check for dial tone. Lift the handset and listen for a dial tone. If you don’t hear a dial tone, see IN CASE OF DIFFICULTY. 1 Wall Installation 1 Remove the base. Slide the base sideways as shown by the REMOVE arrow. 2 Install the batteries as shown in Step 2 under Table/Desk Installation. 3 Connect the short line cord to the telephone. Plug the short line cord into the LINE jack on the back of the set. Feed the cord through the channel on the bottom of the set. 4 Reinstall the base. Turn the base so that the larger end is toward the bottom of the telephone. Insert the base tabs into the slots. Then slide sideways in the direction of the INSTALL arrow to lock the base onto the phone. I N S T A L L A T I O N 2 figure 1 figure 2 figure 3 5 Reverse the handset tab. To mount the telephone on a wall, you must reverse the handset tab. This tab holds the handset when you hang up. Hold down the switchhook, and slide the tab up and out of its slot (figure 1). Turn the tab so that the end with the “hook” is up (figure 2). Then insert the tab back into its slot (figure 3). 6 Connect the line cord to the modular jack and mount the phone onto the wall jack. Plug the free end of the line cord into a modular wall jack. Make sure the cord snaps firmly into place. Place the phone on the wall jack mounting studs and pull down until it is held securely. 7 Follow Steps 6–8 under Table/ Desk Installation. F E A T U R E S E T U P Turn System On/Off Before proceeding to set up features, press O to turn the system on. The PLAY/ STOP light is on or blinking when the system is on. Feature Setup 1 To enter Feature Setup mode, press and hold Suntil the system announces “Selected announcement is…” 2 Press and release Suntil the system announces the feature you want to set. Feature Summary 3 Press and release or until the system announces the setting you want. Refer to the Feature Summary for options. 4 Press and release Sto set up the next feature listed on the Feature Summary — OR — Press and release P to exit Feature Setup. The new settings will be saved. Feature/System Announces Options Announce Select Choose to record an announcement, or use the pre-recorded announcement. “Selected announcement is...” • Select “Announcement A” when you want the system to record callers’ messages. Select “Announce Only” when you want the system to play an announcement and then hang up. • If you select “Announcement A” and do not record an announcement, the system plays the pre-recorded announcement: “Hello. Please leave a message after the tone.” • If you select “Announce Only” and do not record an announcement, the system will answer after 10 rings and announce “No announcement.” See “Record Your Announcement”under ANSWERING SYSTEM OPERATION for recording instructions. Number of Rings Choose how many times the line will ring before the system answers a call. “Number of rings is...” • Set for 2 to 7 rings, or choose Toll Saver 2/4 or Toll Saver 4/6. • When set to Toll Saver 2/4, the system answers after four ring...