Votos - 5, Puntuación media: 4.4
(
)
)
|
Resumen del manual
Please read Part 1 — Important Product Information, included in this package. Part 2 © 1998 Philips Consumer Communications, L.P. All rights reserved. Printed in Mexico. 848236337 Issue 1AT&T I N S TA L L AT I O N NOTE: This telephone requires a modular telephone jack. Table If you have a wall-mounted telep h o n e, remove the telphone from the wall and follow these instructions: 1 Remove the base. 2 Connect line cord to telep h o n e. Plug the line cord into the LINE j a ck on the bottom of the telep h o n e. 3 Attach the base. Turn the base so that the larger end of the base is toward the top of the telephone. Attach the base by inserting the tabs into the slots. Push down on the large end of the base to lock it into place. 4 Connect the line cord to your modular jack. Plug the free end of the line cord into a modular jack. Make sure it snaps firmly into place. 5 Connect handset to telephone. Plug the coiled cord into the handset jack on the side of the phone. Plug the other end of the coiled cord into the handset, and then hang up. 6 Check for dial tone. Lift the handset and listen for a dial tone. If you cannot hear a dial tone, turn to “In Case of Difficulty.” Wall 1 Remove the base. 2 Connect the line cord to telephone. Do not unbundle line cord. Plug the seven-foot line cord into the LINE jack on the underside of the phone. Leave enough cord free to connect to the wall jack, but keep any excess cord bundled. Store the bundled cord in the open area under the set. 3 Attach the base. Turn the base so that the larger end of the base is toward the bottom of the telephone. Attach the base by inserting the tabs into the slots. Push down on the large end of the base to lock it into place. 4 Reverse handset tab. To mount the telephone on a wall, you must reverse the handset tab. This tab holds the handset when you hang up. Hold down the switchhook, and slide the tab up and out of its slot (Figure 1A). Turn the tab so that the curved end is up (Figure 1B). Then insert the tab back into its slot (Figure 1C). 5 Connect the line cord to modular wall jack and mount phone onto wall jack. Make sure the cord snaps firmly into place. Place the phone on the wall jack mounting studs and pull down until it is held securely. Follow Steps 5 and 6 under “Table” Installation. Dial Mode Selection This telephone will wo rk with tone or dial pulse (ro t a ry) serv i c e. Even wh e n set to dial pulse serv i c e, the phone can be sw i t ched tempora ri ly to tone, for access to services that re q u i re tone signaling, i n cluding some t o n e - a c t ivated computer systems. This product comes set in the touch-tone mode. Make sure you choose the correct dialing method; touch-tone dialing will not work if you have dial pulse service. After the telephone is plugged in, if you have dial pulse (rotary) service, lift handset and press , , , , . Return the handset to the base to activate. To change back to touch-tone service, lift the receiver, then press , , , , and return the handset to the base. To switch from pulse to tone dialing during a phone call, see “Temporary Tone Dialing.” Figure 1A Figure 1B Figure 1C 1 TELEPHONE OPERAT I O N Handset Switchhook (under handset) Directory Card/Cover Accesses one-touch memory dialing numbers Programs a number in memory Accesses speed dial memory numbers Temporary Tone Ringer Volume Puts a call on hold Mutes a call Redials last call made Speaker/Handset Access Call Waiting Volume or other services Turns speaker on and makes a call 2 TELEPHONE OPERAT I O N c o n t i n u e d Making and Answering a Call—Handset Lift the handset to make and receive calls as you usually would. Making and Answering a Call— Speakerphone N OT E : The red speakerphone light will go on when the speakerphone is being used. To make a call using the speake r- p h o n e, p ress and hold u n t i l the speake rphone light comes on, wa i t for dial tone, then dial (either manu a lly or using the memory fe at u re ) . To answer a call using the speakerphone, press and hold until the speakerphone light comes on (do not lift handset). When the call is finished, press again to hang up. To switch from handset to speakerphone, press . To switch from speakerphone to handset, lift the handset. N OT E : Using an extension phone is not recommended while using the speakerphone. Volume Button The VOLUME button adjusts the speaker or the handset during your call. Adjusting one does not affect the other. When on a call, press to increase volume, to decrease volume. Redial The telephone stores in memory the last number you called. The number (up to 24 digits) will remain in the Redial memory until you dial another number. To dial the same number again, lift the handset or press , listen for the dial tone, and press . To erase Redial, press , , then again. Hold The Hold feature allows you to keep a call on the line while you step away from the phone or while someone takes the call on an extension phone. When a call is on Hold, the red HOLD ...