Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
All rights reserved. Printed in Mexico. 848234050 Issue 1AT&T AT&T 135 Quark pdf 7/22/98 11:26 AM Page 2 PA RTS CHECKLIST Remember to save your sales receipt in case you ever need warranty service, and make sure this telephone package includes the items shown below: 7-foot line cord 5-inch line cord Coiled handset cord T e l e p h o n e B a s e H a n d s e t R i n g e r V o l u m e Dial Mode S w i t c h 1 AT&T 135 Quark pdf 7/22/98 11:26 AM Page 3 I N S TA L L AT I O N Dial Mode Switch Selection Set the Dial Mode switch on the side of the set to TONE (touch tone) or PULSE (dial pulse/rotary) telephone service. Make sure you choose the correct dialing method; touch tone dialing will not work if you have dial pulse service. The temporary tone dialing is activated by pressing while in pulse mode. T a b l e 1 . Remove the base by sliding it sideways as indicated by the “REMOVE” arrow. 2 . Connect long line cord to telephone. Plug the line cord into the LINE jack on the bottom of the phone. 3 . Reinstall the base with the wide edge at the back of the telephone. Insert the base tabs into the slots on the bottom of the telephone and feed the line cord through the hole in the wide end of the base. Turn the telephone right-side up; it should sit flat on your table during use. 4 . Set the Dial Mode switch. The Dial Mode switch is on the side of the phone. Use a ball point pen to set the switch to TONE if you have tone telephone service, or to PULSE if you have dial pulse (rotary) telephone service. 5 . Connect line cord to modular wall jack. Plug the free end of the line cord into a modular wall jack. Make sure it snaps firmly in place. 6 . Connect handset to telephone. Plug the coiled end into the handset jack on the side of the phone. Plug the other end of the coiled cord into the handset, then hang up. W a l l 1 . Remove the base. 2 AT&T 135 Quark pdf 7/22/98 11:26 AM Page 4 I N S TA L L ATION (c o n t i n u e d ) 2 . Connect short line cord to telephone. Plug the 5-inch line cord into the LINE jack on the bottom of the phone. 3 . Reinstall the base. Turn the base so that the larger end is toward the bottom of the telephone. Reinstall the base by inserting the top tabs into the phone slots. Then slide sideways in the direction of the “INSTALL” arrow to lock into the phone. 4 . Reverse the handset tab. To mount the telephone on a wall, you must reverse the handset tab. This tab holds the handset when you hang up. Hold down the switchhook, and slide the tab up and out of its slot (Figure 1). Turn the tab so that the end with the “hook” is up (Figure 2). Then insert the tab back into its slot (Figure 3). Figure 1 Figure 2 Figure 3 5 . Connect the line cord to the modular jack and mount the phone onto the wall jack. Plug the free end of the line cord into a modular wall jack. Make sure the cord snaps firmly into place. Place the phone on the wall jack mounting studs and pull down until it is held securely (Figure 4). Figure 4 3 AT&T 135 Quark pdf 7/22/98 11:26 AM Page 5 O P E R AT I O N R e d i a l The telephone always stores in memory the last number dialed. To dial the same number again, press . The redial memory can accept numbers up to 24 digits long. The number will remain in memory until you change it by dialing another telephone number. For privacy, you can erase the redial memory. Lift the hand set, then press any digit (1-9). F l a s h Press instead of pressing the switchhook to activate customer calling services such as call waiting or three-way calling. You may have to press other buttons before or after as explained in custom calling instructions provided by your local telephone company. Ringer Volume The RINGER volume switch allows you to adjust the loudness of the telephone ringer from OFF to HI. Slide the switch to the desired volume level. Volume Buttons The VOLUME button adjusts the handset during your call. While on a call, press to increase volume, t o decrease volume. Dial Mode This telephone has a selectable push-button dial and will work with either tone or rotary telephone service. It can be set to work directly with long distance or certain other services that require tone signaling including some tone activated computer systems. (Turn over for more Operation, Memory and In Case of Difficulty) 4 AT&T 135 Quark pdf 7/22/98 11:26 AM Page 6 O P E R ATION ( c o n t i n u e d ) Temporary Tone Dialing Temporary tone dialing is used only when you have rotary service. It allows you access to services that require tone signaling, including some tone- activated computer systems (e.g., telephone banking). To change from pulse (rotary) to tone dialing during a call: 1 . Dial a telephone number with the dial mode switch set to P U L S E . 2 . Press ; all buttons pressed after this will send tone signals. 3. After you hang up, the phone automatically returns to rotary service. M E M O RY Memory Features Numbers will remain stored in memory unless you erase or change them by entering other numbers. C a p a c ...