Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alternations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. “The Ringer Equivalence Number is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.” E - 6 9038_1_ib_e.p65 6 10/31/03, 12:13 PM INSTALLATION Handset Installation and Charging Plug the AC/DC adaptor jack into the back of the charger and then plug the AC/DC adaptor into a compatible wall socket. The rechargeable battery pack must be charged for approximately 10 hours before first use. The battery pack will not have been inserted into the handset so please insert the battery pack into the back of the handset. Place the handset into the cradle and the CHARGE LED should light, indicating the battery pack is being charged. After 10 hours, your telephone will be ready to use. Placing the Battery Pack • Remove the battery door to slide downward. • Connect the new battery pack into the battery compartment. • Replace the battery door to slide upward. NOTE : When the handset is first time power up, the display will show “REGISTER”, press YES (3) to start registration and then : • Press and hold the PAGE button on the new station, (about 6 seconds), until the LED flashes and release the PAGE button after stops (flashing). This will put the base into subscription mode for about 5 minutes. • Enter the PIN code “4321” then press YES (3) to confirm • Press scroll keys 5/6(6) to select a new base ID number for new base station. • Press YES (3) to confirm the base number, then handset will start the subscription and “SEARCHING. . . “ is displayed. • “REGISTERED x” will be displayed for a few seconds and then “H x” be shown on LCD if the subscription is successful. Else, “H ?” will be shown for fail subscription. For detail procedure, please refer page E-10 for registration again. E - 7 9038_1_ib_e.p65 7 10/31/03, 12:13 PM INSTALLATION Install charger unit in a location where: • Away from electrical appliances, such as computer, TV, microwave ovens, wireless equipment or another cordless phone. • In a HIGH and CENTRAL location with no obstructions & barriers, • Being visible at most of your area. E - 8 9038_1_ib_e.p65 8 10/31/03, 12:13 PM E - 9 HANDSET SECTION 1) RECEIVER 2) DISPLAY 3) OFF HOOK / YES / FLASH KEY 4) INT/REDIAL / PAUSE KEY 5) ON HOOK / NO KEY 6) SCROLL KEYS 5/6 7) DIAL KEYS / ID#’s 8) SPEAKER KEY 9) MICROPHONE 10) STRAP HOLDER 11) SPEAKER 12) BATTERY DOOR 13) HEADSET JACK LOCATION OF CONTROLS CHARGER SECTION 14) CHARGE LED 15) ADAPTOR SOCKET ACCESSORIES 16) CHARGER ADAPTOR 17) BATTERY PACK ICON EXPLANATIONS RECEIVED SIGNAL STRENGTH INDICATOR (RSSI) : On when registered and in range, flashes when out of range. RINGER MUTED : On when ringer volume is set to zero. LINE INDICATOR : On when the handset is on line. BATTERY STRENGTH : Three segments to indicate state of charge of battery. Flashes when battery needs recharging. 14 15 12 16 17 9038_1_ib_e.p65 9 10/31/03, 12:13 PM E - 10 SUBSCRIBING HANDSET TO BASE STATION DELETING A BASE STATION If the user wants to remove the entry for the base station from the handset’s memory, this process can be undertaken whether or not the handset is within range of the base station concerned. • Press scroll keys 5/6(6) to select “ADVANCED”, then press * to confirm. • Press scroll keys 5/6(6) again to select “DELETE”, then press YES (3) to confirm. • Enter the PIN code then press YES (3) to confirm • Press scroll keys 5/6(6) to select a base ID number that to be deleted, then press YES (3) to confirm. • Handset will show “PLEASE WAIT” then “SEARCHING. . . “ is displayed. SUBSCRIBING HANDSET TO TL1102 BASE STATIONS This is the case when the user wishes to add a subscription to a base station. • Press and hold the PAGE button on the new stat...
Otros modelos de este manual:Teléfonos fijos - 4GHz (902.26 kb)