Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Glen Harbor Blvd., Glendale, AZ 85307 NLM055Y2 Printed in China IB-4577B CID110 Owner’s Manual IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire.They may explode. Check with local codes for possible special disposal instructions. SAVE THESE INSTRUCTIONS LOCATION OF CONTROLS 1 2 3 4 5 6 7 8 9 1. Receiver 2. Receiver Volume Control 3. Hook Switch 4. Keypad 5. Tone/Pulse Switch 6. Redial Button 7. Transmitter / Mic 8. Store Button 9. Memory Button 10 11 12 13 14 15 16 10. New Call LED 11. Ringer Hi/Lo/Off Switch 12. LCD Display 13. Battery Compartment 14. Review / Button 15. Erase Button 16. Call Back Button CONGRATULATIONS! You have purchased a CID110, Caller ID Telephone with 10Memory Dialing manufactured to the highest standards of ConairphoneTM. Before installing and operating, be sure to read this manual. GENERAL INFORMATION UNPACKING This package contains: • CID110 Caller ID Telephone with 10-Memory Dialing • Owner’s Manual • Fully Modular Coil Cord • Fully Modular Telephone Line Cord (Long Straight Cord) • Fully Modular Telephone Line Cord (Short Straight Cord) • Quick Installation Guide • Important Notice • Two (2) Memory Index Labels • Warranty Card If anything is missing or damaged, contact the place of purchase. Keep the packaging to transport telephone. For your reference, keep a record of the date purchased. Please save the sales receipt for the warranty reference. Date of Purchase ___________________________ INSTALLATION INSTRUCTIONS Follow these precautions: a. Never install telephone wiring during a lightning storm. b. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. c. Never touch uninsulated telephone wires or terminals unless the incoming telephone line has been disconnected at the network interface. d. Use caution when installing or modifying telephone lines. 12 3 TO INSTALL BATTERIES Batteries are required for the Caller ID functions and Telephone operations of the unit. 1. Open the battery door by pulling back the latch. 2. Insert three (3) AA alkaline batteries (not included). 3. Snap the battery door back into place. Note: Once batteries are installed, you have 20 seconds to setup the Caller ID. SETTING UP YOUR CID110 DO NOT CONNECT the line cord to the wall outlet until the Caller ID setup has been completed. NOTES: • If the Caller ID is not setup within 20 seconds after battery installation, press and hold both the [ ] and [ ] keys for 4 seconds to activate the Caller ID setup. • If you do not have the Caller ID service and want the time/ date set, please go to Caller ID setup section and ‘ENTER TIME DATE’ setting. The LCD shows ‘ENTER LANGUAGE’ followed by a choice of 3 languages (English, Spanish, French). The LCD then shows ‘ENG ESP FRA’. NOTE: The ‘ENG’ is BLINKING. Press [ ] or [ ] to select ‘ENG’, ‘ESP’, or ‘FRA’. Press [ERASE] to confirm. If ENG is selected, the LCD shows ‘LCD CONTRAST’. Press [ ] or [ ] to adjust five levels (from 1 to 5, default is 3) contrast of LCD. Press [ERASE] to confirm. If contrast is set, the LCD shows ‘ENTER AREA CODE’. The first digit ‘–’ of the area code will blink. Press [ ] or [ ] to enter the area code. Press [ERASE] to confirm and go to next entry. Repeat above steps until 3-digit area code is set. If area code is set, the LCD shows ‘ENTER TIME DATE’. Press [ ] or [ ] to select the hour digits. Press [ERASE] to confirm and go to the next entry. Press [ ] or [ ] to select the minute digits. Press [ERASE] to confirm and go to the next entry. Press [ ] or [ ] to select the month digits. Press [ERASE] to confirm and go to the next entry. Press [ ] or [ ] to select the date digits. Press [ERASE] to confirm. The LCD shows ‘TOTAL:00 NEW:00’, which means both the total call and new call counter are zero. USING THE PHONE ON A DESK 1. Plug the long telephone line cord into the jack in the bottom of the BASE, thread it through the groove toward the back of the unit, then plug it into the modular phone jack. 2. Connect the COIL CORD to the jack in the HANDSET and the BASE. HANGING THE PHONE ON THE WALL When the CID110 is wall mounted, the HANDSET GUIDE holds the handset in place in the cradle. On a wall phone plate 1. Plug the short telephone line cord into the jack in the base bottom and into the jack on the plate. 2. Hang the base on to the two pins and pull the base dow...