Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
MONITOR HOLD OFF 1 3 2 4 VOLUME TALK ACTIVE Program Additional Intercoms 1 2 Troubleshooting Intercom does not function. Check batteries in intercom. If using a DC Adapter ensure that it is plugged in. Ensure intercom is connected to a network. See Program. Ensure that intercoms are on the same channel. See Operation. The intercom can be programmed to at least one other intercom to become a network or it can be programmed into an existing network. CREATE NEW NETWORK Before programming, clear memory on all intercoms. Press the Learn button on the new intercom until a beep is heard. Each intercom will emit a tone when entering programming mode. It may take up to 3-1/2 minutes for a secure network to be established. MONITOR HOLD OFF 1 3 2 4 VOLUME TAL K ACTIVE HOLD ACTIVE TALK 1 3 2 4 VOLUME MONITOR CHANNEL OFF Within 10 seconds put the second intercom into Learn Mode (press the Learn button until a beep is heard). Press and release the Talk button to verify network is complete. VOLUME MONITOR CHANNEL HOLD OFF ACTIVE TALK 13 2 4 Intercom is not getting expected transmission range. Keep antenna vertical. Keep intercom away from metal objects and electrical wiring. Cell phones, cordless phones, or other radio devices may also limit range. 1 2 3 1 2 3 Troubleshooting Intercom beeps every ten minutes. The battery is low in the intercom. Replace with AA Alkaline batteries or operate it with DC Adapter (not provided). A 12 volt, 300mA DC Adapter may be used (center positive polarity on the round plug). Need to clear intercom’s memory. Press and hold Learn button, an initial beep will be heard. Continue to hold until a second beep is heard (about 6 seconds). Ensure other intercoms are not activated during this time. Once memory is clear the intercom can be programmed to a new network. Static and feedback is heard in intercom. The intercoms are too close to each other. A cordless phone, cell phone, or other radio devices can also cause static. Intercom is sending audio while no buttons are pressed. The sending intercom is set to Monitoring Mode or Voice Activation Mode and will activate when sound is heard. It can be taken out of Monitoring Mode by pressing the Talk button. It can be taken out of Voice Activation Mode by setting Dipswitch #1 to DOWN position. See Features. Doorbell does not function. Check batteries in doorbell. When you press the Call button you should hear a tone. Ensure doorbell is connected to a network. See Program Intercom to Doorbell. The doorbell will not function when an intercom is in Monitor Mode. Doorbell is not getting expected transmission range. Keep doorbell away from metal objects and electrical wiring. Do not mount doorbell on a tree, masonry, or metal surface. When used in buildings with stucco or cement walls, the range is greatly reduced. Warranty ONE YEAR LIMITED WARRANTY The Chamberlain Group, Inc. warrants to the fi rst retail purchaser of this product that it is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Doorbell beeps every ten minutes. The battery is low in the doorbell. Replace with AA Alkaline batteries. Need to clear doorbell’s memory. Press and hold Learn button, an initial beep will be heard. Continue to hold until a second beep is heard (about 6 seconds). Once memory is clear the doorbell can be programmed to a new network. Intercom can not be programmed to network. A network may contain up to 12 intercoms. It may be necessary to clear the network and reprogram all the intercoms to the network. See Programming Intercom. The intercom does not connect to another intercom and a green light is on longer than 3-1/2 minutes. The intercom is out of range. Place the intercom closer to the other intercoms in the network, with the antenna pointing up. The other intercom in the network has no power. Replace the batteries. The intercom has not completed programming. Clear th...
Otros modelos de este manual:Teléfonos fijos - NDIS (1.7 mb)