Iniciar sesión:
Votos - 2, Puntuación media: 3.5 ( )

Manual de usuario Clarity, modelo RC200

Fabricar: Clarity
Tamaño del archivo: 994.37 kb
Nombre del archivo:
Idioma del manual:enfr
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Tone/pulse switch set to Tone. TO CHANGE MODES OF OPERATION Setting the Scan Function If you have RCI00 To turn Scan function off (or on): o Press PROGRAM. If you have RC200 To turn Scan function off (or on): O Press PROGRAM. To turn Voice Activation on (or off), (RC200 only): o Press PROGRAM. To turn the Unanswered Call Indicator feature off (or on): o Press PROGRAM. To turn the Voice Mail Indicator feature on (on off), (RC200 only): o Press PROGRAM. PROGRAMMING NUMBERS INTO MEMORY o Press PROGRAM. MAKING A CALL BY DIALING ON THE RC A. From the keypad o Press ON/OFF button. B.Auto Dialing the first number stored in MI o Press ON/OFF button. C. Memory Dialing stored number, twice for the second number. o Press a memory button once to dial the first MAKING A CALL USING THE REMOTE TRANSMITTER A.With Scan function on © Press Remote Transmitter once. B.With Scan function off O Press Remote Transmitter once. ANSWERING A CALL A. From the keypad © Press ON/OFF button to answer. B. Using the Remote Transmitter Q Press Remote Transmitter once to answer. C. Using Voice Activation, (RC200 only). O Say “Hello” or whistle between rings to turn on phone. 10 • Voice Activated answering is off, (RC200 only). • Ring volume set to Hi. • Unanswered call indicator is • Voice Mail indicator is off, on. (RC200). • ”0“ (operator) is programmed into • Remote Flash switch is off, the first memory location of MI. (RC200 only). © Press 0 on the keypad to turn it off; or Press 1 key on the keypad to turn it on. © Press SCAN button. © Press 0 key to turn it off; or Press 1-9 keys to turn it on. See Page 5 for rate selection guide. © Press SCAN button. © Press MUTE twice. © Press HEADSET twice. © Press FLASH/PAUSE twice. © Dial the number (up to 40 digits). © Select the memory button. Press once for first location, or twice for second location. © Dial the number. © Press ON/OFF button to hang up. © The number is dialed in 7 seconds. © When the desired directory location is lit, press it again. © Press Remote Transmitter to hang up. © The first number stored under MI is dialed. © Press Remote Transmitter once to hang up. © Press ON/OFF button to hang up. © Press Remote Transmitter once to hang up. © It hangs up automatically after one minute of silence or when it detects dial tone. CHAPTER 7 IN CASE OF DIFFICULTY If any problem should occur during operation of your RC, review the list below. Should the difficulty persist, contact AMERIPHONE or your authorized dealer before sending the phone for service. SYMPTOM CAUSE AND REMEDY No dial tone - Check all phone line connections. No power - Check power connection. Does not dial out - Check all phone line connections and power connection. - Change to pulse dialing and try again. Does not dial memory number - No number programmed in memory. Remote Transmitter does not work - Check or replace battery. - Check channel settings. - Make sure no part of the RC system is on or near metal surfaces or electrical equipment. No audible ring - Make sure the ringer is not set to "Off position. Does not scan through memory - Turn on Scan function. Scanning too fast/slow - Program Scan rate to a slower/faster setting. (Dialogue RC200 only.) Cuts in and out while speaking/ listening - Avoid speaking at the same time as the other party. Take turns. SENSITIVITY ADJUSTMENT YOU MUST CONTACT AMERIPHONE BEFORE MAKING THE FOLLOWING ADJUSTMENT: Callers can't hear your voice when using the optional headset with integrated microphone - Turn HEADSET MIC GAIN adjustment, located on bottom of unit, clockwise to increase sensitivity, counterclockwise to decrease. 12 CHAPTER 7 (CONTINUED) CHANNEL SETTINGS The RC and Remote Transmitter use radio signals to communicate with each other. For the Remote Transmitter to activate the RC, they both have to be on the same "channel." A "DIP Switch" is used for channel selection. Your phone and remote have been preset at the factory to a standard channel setting. Under normal operating conditions, there is no adjustment necessary. If your system encounters interference and repeatedly activates by itself for no obvious reasons, it may be necessary to change DIP Switch settings on the RC and Remote Transmitter. 1. Unscrew bottom of the Remote FiSure 24 - Cha""e' setuP Transmitter. 2. Locate DIP Switches on Remote Transmitter and on bottom of RC. 3. Using a ball point pen, change the settings on all switch positions to match exactly on both RC and Remote Transmitter. 4. Replace remote cover and test. 13 CHAPTER 8 CHAPTER 9 MAINTENANCE REGULATORY INFORMATION To ensure trouble-free service, your RC should always be treated with care. Do not drop or subject the phone to high impact. The unit can be cleaned with a damp cloth and a mild detergent. Never use abrasives or solvents. Keep the unit plugged into the electrical outlet at all times, except when cleaning.This will automatically recharge the optional back-up...

Otros modelos de este manual:
Teléfonos fijos - RC100 (994.37 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría