Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
20). —12 levels (1-12) while using the speakerphone (p. 20). 11:50^11/24 NO ITEMS STORED The Caller List is empty. 11:50™11/24 x3\m ^1-111-444-7777 TINA ROBINSON This is a display from the Caller List. The display shows: —the time and date of the last call (Ex. Nov. 24, 11:50 AM), —the number of times called (Ex. 3 times), —the caller information is new and has not been viewed (“G33” is displayed), —the called line, —the caller’s number and —the caller’s name. Connecting the Handset/AC Adaptor Power Outlet oUSE ONLY WITH Panasonic AC ADAPTOR KX-TCA1 (Order No. KX-TCA1-G). °Use only a Panasonic Handset for the KX-TSC14W. oThe AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) о During a power failure the unit will work as a standard telephone on the Line 1, but the following features will not work. —Caller ID services —speakerphone —line indicators —LCD display 8 C> Conneciing the Telephone Line Cord Connect the telephone line cord(s) to the unit as follows. To connect a two-line telephone jack Two-Line Telephone Jack (RJ14C) & Settings To connect two single-line telephone jacks Fasten the telephone line cords to prevent them from being disconnected. OD HI C GREEN plug TRANSPARENT plug 4-Wire Telephone Line Cord LINE 2 rs* with GREEN Plugs --1-. Single-Line Telephone Jack (RJ11C) ^ «3 ]-—=JD 2-Wire Telephone Line Cord with TRANSPARENT Plugs LINE 1 If you use the unit only as a single-line telephone 2Q Hook FS Sfl Fasten the telephone line cord to prevent it from being disconnected. V7 hu£ TRANSPARENT plug Single-Line Telephone Jack (RJ11C) ^ 2-Wire Telephone Line Cord with TRANSPARENT Plugs • For this connection, you can only use LINE 1. 10 o Connecting a Communication Device After connecting the telephone line cord to a two-line telephone jack, you can connect a communication device (computer, modem, fax, answering machine, etc.) through this unit using the LINE 2/DATA jack (—Data Port). Two-Line Telephone Jack (RJ14C) oif the LINE 2/DATA indicator lights, the communication device is in use. Use LINE 1 to make a call. Otherwise the communication device may not operate properly. 0> Settings Setting the LCD Contrast You can select the LCD contrast level from 1 to 6 by programming. Your phone comes from the factory set to 3. Make sure that the handset is on the cradle, the AC adaptor is connected and the SP-PHONE/HEADSET indicator light is off. Press (FUNCTION/EXIT). 2 Press Q or Q repeatedly until “LCD contrast ?” is displayed. 3 Press [>D OK/EDIT. ©The current setting is displayed. 4 Press © or 0 to select the desired LCD contrast level. oEach time you press Q or 0, the level will change on the display. 5 Press ® OK/EDIT. oThe display will return to step 2. To return to the standby mode, press (FUNCTTon/EXITI or wait for 60 seconds. 9:30^12127 SAVE AUTO# ? 9:30ph12/27 LCD CONTRAST ? 9:30ml 2! 27 □□□ 12 o Selecting the Dialing Mode You can select the dialing mode by programming. If you have touch tone service, set to “TONE”. If rotary or pulse service is used, set to “PULSE”. Your phone comes from the factory set to “TONE”. Make sure that the handset is on the cradle, the AC adaptor is connected and the SP-PHONE/HEADSET indicator light is off. Press I FUNCTION/EXIT). 2 Press 0 or 0 repeatedly until “set dial mode ?” is displayed. 4 Press 0 or 0 to select “tone” or “PULSE”. 5 Press ® OK/EDIT (save key). oA beep sounds. oThe display will return to step 2. To return to the standby mode, press (FUNCTION/EXIT| or wait for 60 seconds. 11:50^11/24 SET DIAL MODE ? 11:50^11/24 TONE t> = SAVE 11:50^11/24 SAVE AUTO# ? oYou can exit the programming mode any time by pressing (FUNCTION/EXIT ]. £> Settings Selecting the Line Mode If a line is connected to a low voltage system such as a PBX, set to “B”. If not, the line indicator will not operate properly. Both lines are preset to “A”. Make sure that the handset is on the cradle, the AC adaptor is connected and the SP-PHONE/HEADSET indicator light is off. 1 Press I FUNCTION/EXIT). ll:50AHll/24 SAVE AUTO# ? 2 Press © or 0 repeatedly until “set line mode ?” is displayed. ll:50™ll/24 SET LINE MODE ? 11:50*" 11/24 LINEl >=NEXT 4 Press 0 or Q to select the desired line, “LINEl” Or “LINE2”. ^ Press © OK/EDIT {next key). 6 Press QorQto select the desired line mode. 11:50™ 11/24 LINE2_E>=NEXT 11:50^11/24 A >=SAVE Press {>} OK/EDIT {save key). oA beep sounds. oThe display will return to step 2. To program the other line, start from step 3. To return to the standby mode, press (FUNCTION/EXIT 1 or wait for 60 seconds. oYou can exit the programming mode any time by pressing [FUNCTION/EXIT]. 14 c> Programming Summary of Preparations You can program the following functions. The display shows the programming instructions. See the corresponding pages for function details. Make sure that the handset is on the cradle, the AC ...