Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
However, standalone voice-mail systems work well with the Line Share 120H. We recommend that call forwarding and the phone company’s voice mail services be discontinued. The Line Share 120H is a state-of-the-art telephone line sharing device that eliminates the extra dedicated telephone lines used to operate a fax, modem, or other telephone devices. The Line Share 120H quickly directs incoming telephone calls to one of three appropriate destinations, typically a computer modem, fax/modem, or fax machine, as well as a telephone and answering machine, or any other telephone device that responds to a standard phone company ring signal. Please read through the rest of this guide to learn how to properly install and operate the Line Share 120H. 9 LINE SHARE 120H 3. Installation The Line Share 120H is a single-line device that can be installed on any type of modular or non-modular system that consists of one or more lines, with one or more phones. A modular system consists of phone cables that can be connected and disconnected from a telephone device. A non-modular system consists of cables that are hard-wired to the telephone device and cannot be disconnected from the equipment. A telephone installer may be required to install the Line Share 120H on a non-modular system. NOTE Many offices have a KSU or PBX phone system. The Line Share 120H works with either of these systems. Simply follow the appropriate installation instructions provided in Section 3.7. 3.1 Unpacking the Line Share 120H When you open the Line Share 120H box for the first time, inspect the contents. You should have the following items: • (1) Line Share 120H • (1) AC power adapter • (1) telephone line cord • This user manual If any of these items are missing or damaged, call Black Box immediately at (724)-746-5500. 10 CHAPTER 3: Installation 3.2 Ports on the Line Share 120H The rear panel of the Line Share 120H includes four (4) modular ports and a power input port, as shown in Figure 3-1. 12VAC FAX/ MODEM 4 PHONE 3 TAD 2 LINE-IN 1 Figure 3-1. Ports on the Line Share 120H. 1. Connect a single telephone line from a standard telephone (wall) jack to this port. 2. Connect your telephone answering device (TAD) or integrated phone/answering machine to this port. The Line Share 120H will route all calls to the TAD and PHONE ports simultaneously. 3. Depending on the installation, a single line phone, and integrated phone/answering machine, multiple phones, or a telephone system (KSU or PBX) can be connected to this port. The Line Share 120H will route all calls to the TAD and PHONE ports simultaneously. 4. The fax machine must be connected to the FAX/MODEM port to enable the Line Share 120H to automatically transfer a fax call with a fax CalliNG (CNG) tone to the fax machine. A computer modem or fax/modem can connect to this port in lieu of a fax machine. 11 LINE SHARE 120H 3.3 Placing the Line Share 120H The Line Share 120H can be placed on either a flat surface, or mounted on a wall. To mount the Line Share on a wall, follow these steps: 1. Mark the positions for 2 mounting screws (not supplied) on the wall. The positions should be 3-1/4” apart (vertically). Drill the 2 holes, then thread the screws into the wall. The screws should extend 3/16”. Do not overtighten the screws. 2. Align the keyholes on the back of the Line Share with the 2 screws, then push in and press down to secure it to the wall. NOTE If you place the Line Share 120H on a flat surface, do not place it close to any peripheral equipment. Keep it approximately 2 to 3 feet (60 to 90 cm) away from all electronic equipment. The Line Share 120H can be mounted on the wall with the connected telephone line cords above or below the unit. Figure 3-2. Bottom of the Line Share 120H. 12 CHAPTER 3: Installation 3.4 Connecting the Line Share 120H This section explains how to install the Line Share 120H in most phone configurations that appear in a home or office. You can install the Line Share 120H in any one of the following phone configurations: • a single phone line with a single phone • a single phone line with multiple single-line phones • a telephone system Installation procedures for each of these configurations are provided in the following sections. To perform the installation procedures in the following sections, you need the following equipment: • telephone cables to connect the Line Share 120H to your telephone (wall) jack. • extension cables—required if the connecting equipment is not located near the Line Share 120H. • additional telephone cables—typically supplied with equipment by the manufacturer. You need additional telephone cables for as many pieces of equipment as you intend to connect to the Line Share 120H. If the equipment manufacturer does not provide the required cables, you can purchase them from your dealer. 3.4.1 INSTALLATION ON A SINGLE-LINE PHONE WITH A SINGLE PHONE Figure 3-3 shows a complete installation for a single phone line/single phone arrangement. While the co...