Votos - 4, Puntuación media: 4.8
(
)
)
|
Resumen del manual
5. Plug the AC power supply cord into the jack on the back of the unit labeled AC 9V. Thread the cord behind the strain relief to stabilize the cord to prevent it from disconnecting easily. Then plug the AC power supply into an electrical outlet. 6. Follow the steps in “Setting Up Your Station Address” to continue installing your phone. CAUTION: Use only the Thomson 5-2418 power supply that is compatible with this unit. Using other power supplies may damage the unit. STORE IN TIMER TIME SET MEMO REVIEW LOWER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 BUSY REDIAL FLASH PAUSE TRANSFER CONF CALL PRIVACY LINE 4 LINE 3 LINE 2 LINE 1 INTERCOM VOLUME HEADSET MUTE SPEAKERPHONE HOLD PAGE WXYZ 9 MNO 6 DEF 3 # TUV 8 JKL 5 ABC 2 OPER0 PQRS7 GHI 4 1 TONE* 4 5 SETTING UP YOUR STATION ADDRESS Your phone has the ability to be set up as either a 2-9451 (the default), or a 2-9450. If you have an existing 2-9450 system, this phone can be set to be fully compatible with your system. See “Changing the Phone to a 2-9450 Model”. VERY IMPORTANT: In order to have full system operation of your phone (i.e. intercom, transfer, page, etc.), lines 1 and 2 must be connected and common to all phones connected to the system. Only other 2-9451 or 2-9450 models are compatible for full system operation. Also, the telephone lines must be connected before AC power is connected. The phone may not install properly, otherwise. The display reads Addr-. 1. Enter the station address number you want to assign (01-16) or press the corresponding memory button. The display 12343 EXT. NUMBERLINE REDIAL DATA PORT TONE STORE IN TIMER TIME SET MEMO REVIEW LOWER indicates what station you have entered. 2. Press the # key to confirm.The INTERCOM indicator flashes red as it checks the system line connections and station 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 BUSY REDIAL FLASH PAUSE TRANSFER CONF CALL address. If the line cords are connected properly and the station address is valid, you will hear a confirmation tone. This indicates that the station address has been successfully assigned. PRIVACY LINE 4 LINE 3 LINE 2 LINE 1 VOLUME WXYZ9 MNO6 DEF3 # TUV 8 JKL5 ABC 2 OPER0 PQRS7 GHI4 1 TONE* HEADSET MUTE SPEAKERPHONE HOLD INTERCOM INTERCOM indicator 3. Push the index cover lock to the left Memory and lift up the acrylic memory index index cover. Remove the memory index Index card Memory indexcard. In pencil, write all the user’s cover cover lock names next to the respective stations on the memory index card. 4. Replace the memory index card, lower the index cover back into place, and push the index cover lock to the right to secure the cover. STORE IN TIMER TIME SET MEMO REVIEW LOWER BUSY REDIAL FLASH PAUSE TRANSFER CONF CALL PRIVACY LINE 4 LINE 3 LINE 2 LINE 1 INTERCOM VOLUME HEADSET MUTE SPEAKERPHONE HOLD WXYZ9 MNO 6 DEF 3 # TUV 8 JKL5 ABC 2 OPER0 PQRS7 GHI 4 1 TONE* 1 5 6 7 8 9 10 11 12 13 14 15 16 NOTE: If you hear an error tone, the station address number you pressed has already been assigned to another phone or the line cords are not properly connected. Check the line cord connections, or change the station address if necessary. NOTE: If you have lines 3 and 4 on your phone, you must program extension numbers for correct operation of the transfer feature. See “Programming the Extension Number”. Lines 3 and 4 DO NOT have to be common for all phones on the system; therefore, the system can have a total of up to 34 lines connected. CHANGING THE PHONE TO A 2-9450 MODEL This phone can also be set up to be compatible with an existing 2-9450 system. 1. Press PROGRAM, which is under the acrylic memory index cover and memory index card. 2. Press 0. 3. Press the # key to confirm. The display reads Addr-. 4. Enter the station address number you want to assign (01-16) or press the corresponding memory button. The display indicates what station you have entered. 5. Press the # key to confirm.The INTERCOM indicator flashes red as it checks the system line connections and station address. If the line cords are connected properly and the station address is valid, you will hear a confirmation tone. This indicates that the station address has been successfully assigned. STORE IN TIMER TIME SET MEMO REVIEW LOWER BUSY REDIAL FLASH PAUSE TRANSFER CONF CALL PRIVACY LINE 4 LINE 3 LINE 2 LINE 1 INTERCOM VOLUME HEADSET MUTE SPEAKERPHONE HOLD PAGE WXYZ9 MNO6 DEF3 # TUV 8 JKL5 ABC2 OPER0 PQRS7 GHI 4 1 TONE* 1 5 6 7 8 9 10 11 12 13 14 15 16 PROGRAM button INTERCOM indicator NOTE : If you program the 2- 9451 as a 2-9450, the Page Group feature will not be available. Line 3 and line 4 must be common for all phones on the system. SYSTEM VERIFICATION The following procedures should be used to test the system’s configuration and identify possible line connection errors. The phone must be connected to the AC power outlet, lines 1 and 2 must be connected to the LINE 1,2 jack, and the phone must be programmed with a station address number. OTHER STATIONS 1. Press LINE 1. 2. Look at all the other s...