Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Check that gate operator has been taught to master unit as well. If OTIUEX has already been programmed and will need to have memory cleared (see below). When dialing numbers a dial tone is heard. All numbers and symbols must be dialed within 3 seconds of each other, otherwise the OTIUEX times out and returns to dial tone. Memory needs to be cleared. Clearing OTIUEX memory will not clear any OTIUEX settings or programmed phone numbers. To clear memory, dial “**#8” on the telephone connected to the OTIUEX. A beep will be heard. To clear DAILM memory, set Dipswitch #1 to the DOWNposition, then press the Learn button until a beep is heard (about 15 seconds). OTIUEX is not getting expected transmission range. When used in buildings with stucco or cement walls, the range is greatly reduced. The Repeaters can be used close to the building to solve this problem. Keep OTIUEX away from trees, metal objects, masonry, computers, and any other “Radio Noise Source”. Radio devices that run on 900 Mhz also affect range. Turn them off and see if reception has improved. Keep antenna vertical. After dialing “*9” a beep is heard, then an error tone. Check batteries in GCU. Will not accept command after dialing “**”. Check the line and telephone connections. Telephone does not ring when Call button is pressed. If the Active LED on OTIUEX flashes after Call button is pressed, check telephone connections. The telephone may not be compatible. Use a 22Vadapter instead of the supplied 18V adapter. This changes the REN# from 3 to 5. If the Active LED on OTIUEX does not flash after the Call button is pressed, see Programming Accessories to ensure OTIUEX is programmed correctly. There is a buzzing or failed connection when call is answered. Move OTIUEX away from phone and/or computer. Try changing channel of OTIUEX and/or the channel on the GAPLM (see Gate Access Panel manual). Only first couple of words from caller are heard. Lower the GAPLM microphone sensitivity (see Gate Access Panel manual). Number Function **01 Enable Call Forwarding **02 Disable Call Forwarding **07 Activating the OTIU **06 Verify Call Forwarding Number **#8Clear Memory *9 Activate Gate **102 - **105 Change number of rings *#(Phone Number)# Program call forwarding number PIN Number Functions To enable Canadian Mode press “**13”. To disable Canadian Mode press “#*16”. The Canadian programming numbers are shown in the table below: Number Function #*01 Enable Call Forwarding #*02 Disable Call Forwarding #*07 Activating the OTIU #*06 Verify Call Forwarding Number #*#8Clear Memory #9 Activate Gate #*102 - #*105 Change number of rings ##(Phone Number)# Program call forwarding number Troubleshooting Dial tone is not heard after connecting to the OTIUEX. Check phone connections. If it is a two-line phone ensure it is on Line 1. If a dual-tone error tone is heard when trying to open gate, ensure OTIUEX is programmed to the correct GAPLM, DAILM, or Intercom. Check that gate operator has been taught to master unit as well. If OTIUEX has already been programmed and will need to have memory cleared (see below). When dialing numbers a dial tone is heard. All numbers and symbols must be dialed within 3 seconds of each other, otherwise the OTIUEX times out and returns to dial tone. Memory needs to be cleared. Clearing OTIUEX memory will not clear any OTIUEX settings or programmed phone numbers. To clear memory, dial “**#8” on the telephone connected to the OTIUEX. A beep will be heard. To clear DAILM memory, set Dipswitch #1 to the DOWNposition, then press the Learn button until a beep is heard (about 15 seconds). OTIUEX is not getting expected transmission range. When used in buildings with stucco or cement walls, the range is greatly reduced. The Repeaters can be used close to the building to solve this problem. Keep OTIUEX away from trees, metal objects, masonry, computers, and any other “Radio Noise Source”. Radio devices that run on 900 Mhz also affect range. Turn them off and see if reception has improved. Keep antenna vertical. After dialing “*9” a beep is heard, then an error tone. Check batteries in GCU. Will not accept command after dialing “**”. Check the line and telephone connections. Telephone does not ring when Call button is pressed. If the Active LED on OTIUEX flashes after Call button is pressed, check telephone connections. The telephone may not be compatible. Use a 22Vadapter instead of the supplied 18V adapter. This changes the REN# from 3 to 5. If the Active LED on OTIUEX does not flash after the Call button is pressed, see Programming Accessories to ensure OTIUEX is programmed correctly. There is a buzzing or failed connection when call is answered. Move OTIUEX away from phone and/or computer. Try changing channel of OTIUEX and/or the channel on the GAPLM (see Gate Access Panel manual). Only first couple of words from caller are heard. Lower the GAPLM microphone sensitivity (see Gate Access Panel manual). Number Function **01 Enable Call Forwarding **02 D...
Otros modelos de este manual:Teléfonos fijos - OTIUEX (77.7 kb)