Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
FCC Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. . 3M 1998 July Model C5000 System Description Introduction System Components Operating Modes STANDBY Mode TALK/LISTEN Mode ALL CALL Mode PAGE Mode Call Merge The 3M™ Convenience Store Intercom System, Model C5000, enables store personnel to communicate with customers calling in from Call Stations at up to 16 pumps or other remote locations. The system arranges incoming calls in a first-come first-served order. The operator can also choose to talk to any customer at any Call Station at any time. Operators using wireless headsets or belt packs can also talk to each other using the paging feature. During peak hours, pushing the FUEL button on the Call Station sends a call to a fuel operator. Pushing the FOOD button sends a call to a food operator. During non-peak hours, pushing either button sends a call to the operator on duty (if this option is installed and selected). Operators use Station Selectors, headsets, belt packs, or a combination of these components to communicate with customers. Figure 1. Station Selector, Headset, and Belt Pack Customers use Call Stations at the pumps to communicate with operators. Figure 2. One-Button and Two-Button 3M™ Call Stations The system can be operated from the Station Selector(s), the headset(s), or the belt pack(s). In the STANDBY mode, the Station Selector, headset, or belt pack is on and waiting to receive a call from a customer or other operators. Use the TALK/LISTEN mode to talk or listen to the customer. Use this mode to talk to all Call Stations at the same time. Use this mode from the headset or belt pack to talk to other operators without the customer hearing the conversation. Use the Call Merge switch to control who receives incoming calls. The Call Merge Switch (not shown) is a single-pole, single-throw switch. NORMAL position is open; MERGE position is closed. Slide the button to MERGE to send all calls to the on-duty operator during off-peak hours. Slide the button to NORMAL to direct FOOD calls to FOOD operators and FUEL calls to FUEL operators during peak hours. . 3M 1998 July Station Selector Controls and Indicators Model C5000 Station Selector The Station Selector controls are shown below. 1 POWER Switch 2 VOLUME Control 3 POWER Indicator 4 Station Selector Keys 5 Call Indicators 1 through 16 (amber) 6 TALK Key 7 TALK Indicator 8 LISTEN Indicator 9 STANDBY Key 10 STANDBY Indicator 11 ALL CALL Key Figure 3. Station Selector, Controls, and Indicators ON turns on the Station Selector; OFF turns it off. • !!!! Note The remotely located communications controller and the Station Selector are designed to be left on. Notify your system administrator or manager if the Station Selector power switch is off and turning it on does not illuminate the power indicator light. Turn to increase; or decrease the volume in the Station Selector speaker. Lights to indicate the Station Selector power is on. Press to initiate or answer a call to a specific Call Station. (Station Selectors come in either 16-station or 8-station units.) Lights in amber to indicate call status: Flashing Light = A call is waiting to be answered. Light Steady On = Call has been answered and connection is established to the customer Press to connect to the calling location. Hold to talk to the customer. Release to listen. Lights (red) when TALK key is pressed and held to indicate the system is in talk mode. Extinguishes when the TALK key is released. Lights (green) when TALK key is released to indicate the system is in listen mode. Press to end a call and return the system to the standby mode. Lights to indicate the system is in standby mode. Press to broadcast a call to all Call Stations at the same time. 2 . 3M 1998 July Model C5000 Station Selector Operating Procedures Operating the Station Selector Responding to a Call Initiating a Call VOX ALL CALL When a customer presses a Call Station button, the amber call indicator key for that Call Station (1 through 16) flashes on the Station Selector and an intermittent tone sounds. The system arranges calls from customers in a first-come first-served order. To answer a call from a Call Station, do the following: 1. Press and hold the TALK key to talk to the first customer in order. • The call indicator light stops flashing, but remains lit. • The red talk indicator lights. • The system automatically connects to the first customer. 2. Release the TALK key to listen to the customer. • The green listen indicator lights. • The call indicator remains lit. 3. When finished talking and listening to the customer, press the STANDBY k...