Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Albans Drive Raleigh, NC 27609 U.S.A. Part Number P-UG-99VO-A Revision 1.1 ©Copyright 2000 Fujitsu Network Communications, Inc. All rights reserved. Printed in the United States of America. This publication may be replaced by a revised edition. To find out if a revision exists, or to order copies of publications, write to Fujitsu Network Communications, Inc., 1000 St. Albans Drive, Raleigh, NC 27609, or call 1-800-228-ISDN. Please direct all communications to End User Products. No part of this publication may be reproduced or translated, stored in a database or retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Fujitsu Network Communications, Inc. The information contained in this document is subject to change without notice. Fujitsu NI / 5E Custom Terminal Intro & Table of Contents 1 Fujitsu NI / 5E Custom Terminal Intro & Table of Contents Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by unplugging the equipment to turn it off, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna of the affected receiver. • Increase the separation between the equipment and the affected receiver. • Connect the equipment to an outlet on a circuit different from the one to which the affected receiver is connected. • Consult a dealer or experienced radio or television technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Notice This telephone is hearing aid compatible. This equipment complies with Part 68 of the FCC Rules. The FCC Part 68 Label is located on the bottom of the enclosure. This label contains the FCC Registration Number for this equipment. If requested, this information must be provided to your telephone company. FCC Regulations require that connection of this telephone to the telephone network be made via an FCC registered NT-1 interface device. Connection to the telephone network should be made via the NT-1 interface by using standard modular telephone jacks, type RJ-49. The plugs and/or jacks used must comply with FCC Part 68 Rules. 2 System Port Identification Facility Interface & Service Order Codes Mfgrs Port Facilities Service Order Network Jack Identifier Interface Code Code ISDN Line 02IS5 6.ON RJ-49 If this telephone equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But, if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the proper functioning of your equipment. If this occurs, you will be notified in advance in order to make necessary modifications to maintain uninterrupted service. Important Safety Information The Fujitsu ISDN Terminal should be used according with all instructions and precautions provided in this guide. • Read and understand all installation instructions. • Install cords where they cannot be a hazard to anyone walking nearby. • Use only a Class 2 power source or communication circuit power source. If you use a local power supply, use Model AD-3645U. • Use only the line cable included with the terminal. • Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or in a swimming pool. • Avoid using the terminal during an electrical storm. There may be a remote risk of electrical shock from lightning. • Do not use the terminal to report a gas leak in the vicinity of the leak. • Do not overhaul or open this product. • Addition and exchanging of hardware options should be performed by authorized personnel. • Use your one-touch numbers for storing emergency numbers. Fujitsu NI / 5E Custom Terminal Intro & Table of Contents 3 Fujitsu NI / 5E Custom Terminal Intro & Table of Contents Repairs Repairs to this equipment can only be made by the manufacturer or its authorized agents. If this equipment is causing harm to the telephone network, the tele...